User manual GRASS VALLEY 8995UDX DATASHEET

[. . . ] 8995UDX Up/Down/Crossconverter and Frame Sync Key Features · Up/down/crossconverter with frame synchronizer · Image enhancement and pixel-level motion adaptive conversion for superb picture quality · Synchronizer for robust signal handling · Full video proc. [. . . ] Powerful embedded audio handling includes channel-level and Dolby E stream routing. PCM audio processing eliminates the clicks caused by the video synchronizer dropping or repeating frames and hot upstream video switching. VITC conversion and Closed Captioning are supported for same frame-rate conversions. One of three types of optional SFP fiber optic submodules can be installed in the fiber optic rear cage connector to provide two fiber inputs (Dual Receiver), two fiber outputs (Dual Transmitter), or one fiber input and one fiber output (Transceiver). Refer to the rear module pinout and the block diagram on the next page. · Where incoming feeds may be in either 1080, 720, or SD formats · For live production where low latency conversion is required · For conversion of signals with embedded audio Specifications Supported Frame Types GeckoFlex with 8900NET (Net Card) for configuration Ordering Information Synchronizing mode = in Minimum Delay Mode (synchronous input): Nominal: 1 frame (±1 pixel) User-adjustable range: 1 frame to 2 frames minus 5 lines Additional adjustable delay: 0 to 6 additional frames Method: Motion adaptive 3:2/2:2 cadence: Automatic detection Input: 1080i or 480i @ 59. 94 Hz, 1080p @ 23. 98, 1080sf @ 23. 98 or 720p @ 59. 94 Hz Output choices: 1080i or 480i @ 59. 94 Hz, 1080p @ 23. 98, 1080sf @ 23. 98 or 720p @ 59. 94 Hz Input: 1080i or 576i @ 50 Hz or 720p @ 50 Hz Output choices: 1080i or 576i @ 50 Hz, 720p @ 50 Hz This module can be mounted in a GeckoFlex frame but not in other 8900 series frames including Gecko-A or Gecko-V frames. As this module has no card-edge controls and in order to configure this module an 8900NET (Net Card) Network Interface module is required. Power Rating and Size Specifications 18 Watts ­ dual slot SD/HD-SDI: One electrical or optional fiber optic ·Inputequalization:upto125m ·Auto-sensing:Yes ·Returnloss:>15dB, 5to270MHz; >15 dB typ, to 1. 5 GHz Auto sensing: Yes Optical: Single-mode (optional) SD/HD-SDI: Four electrical and up to two additional optional fiber optic ·Returnloss:>15dB, 5to270MHz; >15 dB typical, to 1. 5 GHz ·Signallevel:800mVp-p±10% ·Rise/falltime(20-80%):140pstypforHD, 500 ps typical for SD ·Outputjitterinframesyncmode, lowjitterapplied: < 0. 2 UI p-p HD > 100 kHz < 1. 0 UI p-p HD > 10 Hz Optical: Single-mode (optional) Inputs Conversion 8995UDX SD/HD video format up/down/crossconverter, front module and dual wide rear module set 8900GEN-SM Genlock submodule. This submodule mounts to the front module to provide reference input for the module and frame reference bus. This is required for frame synchronizing operation. Outputs Aspect Ratio Conversion Conversion modes: 1:1, letterbox, pillarbox, anamorphic, 14:9 SFP-13103G-M1TRX Fiber transceiver. [. . . ] Amp Channel Gain Motion Adaptive Scaler Channel Stream Routing Embedder SD/HD SDI In DeEmbedder Video Synchronizer & Delay Adjust Audio Synchronizer 4X SD/HD-SDI Out Dolby E and Non-PCM Path Ref In Loop 8900GEN-SM Submodule Option Genlock Adjustment Audio Delay Out Frame Bus 1 Frame Bus 2 [. . . ]