User manual GRASS VALLEY 8995UPC DATASHEET

[. . . ] 8995UPC Upconverter and Frame Sync Key Features · High-quality upconverter with synchronizer for robust signal handling · Image enhancement and pixel-level motion adaptive conversion for superb picture quality · Full video proc. [. . . ] PCM audio processing eliminates the clicks caused by the video synchronizer dropping or repeating frames. This module silences the effects of hot upstream video switching using a V-fade. VITC and closed caption data conversion are supported for same-frame-rate conversions, making this an ideal module for playout applications. One of three types of optional SFP fiber optic submodules can be installed in the fiber optic rear cage connector to provide two fiber inputs (Dual Receiver), two fiber outputs (Dual Transmitter), or one fiber input and one fiber output (Transceiver). Refer to the rear module pinout and the block diagram on the next page. · Where incoming feeds may be in either 480i or 576i SD video formats and require upconversion to HD video · For live production where low latency conversion is required · For conversion of signals with embedded audio Specifications Supported Frame Types GeckoFlex with 8900NET (Net Card) for configuration Synchronizing mode = in Minimum Delay Mode (synchronous input): Nominal: 1 frame (±1 pixel) User-adjustable range: 1 frame to 2 frames minus 5 lines Additional adjustable delay: 0 to 6 additional frames Method: Motion adaptive 3:2/2:2 cadence: Automatic detection Input: 480i @ 59. 94 Hz Output choices: 1080i @ 59. 94 Hz, 1080p @ 23. 98, 1080sf @ 23. 98, or 720p @ 59. 94 Hz Input: 576i @ 50 Hz Output choices: 1080i @ 50 Hz, 720p @ 50 Hz Ordering Information This module can be mounted in a GeckoFlex frame but not in other 8900 series frames including Gecko-A or Gecko-V frames. As this module has no card-edge controls and in order to configure this module an 8900NET (Net Card) Network Interface module is required. Power Rating 18 Watts ­ dual slot SD-SDI: One electrical or optional fiber optic ·Inputequalization:upto125m ·Auto-sensing:Yes ·Returnloss:>15dB, 5to270MHz; >15 dB typical, to 1. 5 GHz Optical: Single-mode (optional) HD-SDI: Four electrical and up to two additional optional fiber optic ·Returnloss:>15dB, 5to270MHz; >15 dB typ. , to 1. 5 GHz ·Signallevel:800mVp-p±10% ·Rise/falltime(20-80%):140pstyp. forHD, 500 ps typ for SD ·Outputjitterinframesyncmode, lowjitterapplied: < 0. 2 UI p-p HD > 100 kHz < 1. 0 UI p-p HD > 10 Hz Optical: Single-mode (optional) Fixed delay mode: Nominal: 2 frames (±1 pixel) User-adjustable range: 2 frames minus 5 lines to 3 frames minus 5 lines Synchronizing mode (asynchronous input): Minimum: 2 frames minus 5 lines Maximum: 3 frames minus 5 lines Fixed delay mode = in Minimum Delay Mode: Nominal: 1 frame (±1 pixel) User-adjustable range: 1 frame to 2 frames minus 5 lines Inputs Conversion 8995UPC SD/HD video format upconverter, front module and dual wide rear module set 8900GEN-SM Genlock submodule. This submodule mounts to the front module to provide reference input for the module and frame reference bus. This is required for frame synchronizing operation Outputs Aspect Ratio Conversion Conversion modes: 1:1, letterbox, pillarbox, anamorphic, 14:9 SFP-13103G-M1TRX Fiber transceiver. [. . . ] Amp Channel Gain Motion Adaptive Scaler Channel Stream Routing Embedder SD SDI In DeEmbedder Video Synchronizer & Delay Adjust Audio Synchronizer 4X HD-SDI Out Dolby E and Non-PCM Path Ref In Loop 8900GEN-SM Submodule Option Genlock Adjustment Audio Delay Out Frame Bus 1 Frame Bus 2 [. . . ]