User manual GRASS VALLEY KAYENNE 2.0 RELEASE NOTES 10-2010

[. . . ] KAYENNE VIDEO PRODUCTION CENTER Release Notes Software Version 2. 0 071868702 OCTOBER 2010 Affiliate with the N. V. KEMA in The Netherlands CERTIFICATE Certificate Number: 510040. 001 The Quality System of: Thomson Inc, and its wor dwide Grass Valley division affiliates DBA GRASS VALLEY Headquarters 400 Providence Mine Rd Nevada City, CA 95959 United States Kapittelweg 10 4827 HG Breda The Nederlands Rue du Clos Courtel CS 31719 35517 Cesson-Sevigné Cedex France 40 Rue de Bray 2 Rue des Landelles 35510 Cesson Sevigné France Carl-Benz-Strasse 6-8 67105 Schifferstadt Germany 15655 SW Greystone Ct. Beaverton, OR 97006 United States 7140 Baymeadows Way Ste 101 Jacksonville, FL 32256 United States 1 rue de l'Hautil Z. I. des Boutries BP 150 78702 Conflans-Sainte Honorine Cedex France Spinnereistrasse 5 CH-5300 Turgi Switzerland 10 Presidential Way Suite 300 Woburn, MA 01801 United States 2300 So. [. . . ] the picture may begin to stretch. 70 KAYENNE -- Release Notes Corner Pinning Corner Pinning with the Multi-Function Module Corner Pinning can be performed from the MFM (Multi-Function Module), in the iDPM (and identically the eDPM), CPin menu. The CPin (Corner Pinning) button has been added to the iDPM menu (Figure 48) in the MFM. Figure 48. MFM--iDPM Key Key Key Key Key Key Wipe ipe Wipe ipe 1 2 3 4 5 6 1 2 SLcX SzLc 3dLc ROT SPIN Axis Adel Last SLcY iDPM ASPT SKEW PRSP 2DLc PGLB Size PGMK2-iDPM SLcX SLcY Size CPin CROP SHAD FILM FRZ SGLB CLR SRC Corner Pinning (Figure 49) and Crop (Figure 50) controls have been added in the CPin MFM menu. Press the CPin button to enable/disable Corner Pinning, press the Dlg button directly below to turn on Corner pinning and adjust the Corner Pinning parameters using the soft knobs. KAYENNE -- Release Notes 8623267_23_r1 PGM Dlg Dlg Dlg Dlg WIPE HOME TARG XFER 71 Version 2. 0 Note Corner Pinning and Crops have their own path controls, however each corner and each crop edge share the same path. See the Kayenne User Manual for more information about paths. Figure 49. MFM--iDPM, CPin (Corner Pinning) Key Key Key Key Key Key Wipe ipe Wipe ipe 1 2 3 4 5 6 1 2 X 9. 000 T/L T/R Adel Last Y -9. 000 iDPM All B/L B/R Thru 50. % CPin Crop Thru X Y Thru PGM Dlg Dlg 8623267_29 The use of the All and corner buttons: T/L--Top Left, T/R--Top Right, B/L--Bottom Left, and B/R--Bottom Right, are the same as in the Corner Pinning menu (see Corner Pinning Menu on page 67). The MFM soft knobs are used for adjusting the corners when selected. The Thru button performs the same function as the View Thru Enable button in the menu but is momentary (opacity setting is only visible when the button is held down). The opacity is adjusted with the Thru soft knob (Figure 49). When Corner Pinning is enabled, and the Crop button is pressed, the All button will be added to the Crop menu. The All button is a toggle that includes All, Pan, and Scan. Z operation of the joystick operates the All crop adjustment (works similar to zoom), X and Y operates as Pan and Scan (Figure 50). Crop All and Crop Edges can be adjusted using the soft knobs (Figure 50). 72 KAYENNE -- Release Notes Corner Pinning Note Crop Softness controls are not available for crops when Corner Pinning is enabled in the MFM, however Crop Softness controls are available in the Menu Panel. Figure 50. MFM--Crop (Corner Pinning, Crop Menu) Key Key Key Key Key Key Wipe ipe Wipe ipe 1 2 3 4 5 6 1 2 CR T 9. 000 SzLc 3dLc ROT SPIN Axis Adel Last CR R 16. 000 iDPM ASPT SKEW PRSP 2DLc PGLB All CR A CPin CROP SHAD FILM FRZ SGLB CLR CR L -16. 000 CR X CR Y CR A PGM Dlg Dlg Dlg Dlg WIPE HOME -9. 000 KAYENNE -- Release Notes 73 8623267_30 CR B Version 2. 0 eDPM Enhancements The eDPM is now completely separate from the rest of the Switcher Master E-MEM so you can recall and run effects from the eDPM independently, or, you can use the Master E-MEM timeline to recall and run the eDPM. This allows you to control the eDPM exactly as you would with an external DPM. Also, you can have multiple E-MEM registers recalling the same eDPM effect. The switcher timeline and the eDPM timeline can now be different registers and have different lengths. If you run the timeline from the eDPM Timeline, it will run the effect as created in the eDPM or if you run it from the Master E-MEM timeline (Switcher mode), it will run until the Master E-MEM timeline is complete. If your E-MEM effect in the Master E-MEM only has one keyframe, you must insert an additional keyframe to run the entire eDPM effect timeline. Note For E-MEMs learned using versions earlier than 2. 0 to work properly, you must reconstruct a timeline for the proxy sublevels to run. The proxy sublevel register has been created but is limited to a single keyframe. Recalling and editing eDPM timelines from the Master E-MEM timeline is truly independent and does not effect the keyframes in the eDPM. Inserting keyframes in the Master E-MEM's eDPM sub-level timeline creates a keyframe which is a `proxy' to drive the eDPM's timeline. · · When running an eDPM timeline from the Master E-MEM timeline, pauses on the eDPM side are ignored. [. . . ] Reactivate any virus protection on the Menu panel that may have been disabled at the start of this procedure. This completes the standard Kayenne system software update procedure. Other Kayenne Systems Software Update More than one Kayenne system (multiple Video Processor Frames) may reside on your network. Each system can operate simultaneously with different software versions, as long as all the components in each system run the same software version. Additional Kayenne systems are updated using the same procedure described before. 1. Select the other Kayenne system on the Kayenne Installer Program System hierarchy screen, and choose Update All. [. . . ]