User manual GRUNDIG FINE ARTS AUDION RCD 8300

[. . . ] FINE ARTS AUDION WIRELESS HIFI SYSTEM Operating manual ENGLISH 55404 941 1200 CONTENTS Dear customers, ________________________________________________________________________ This operating manual assumes that your authorised dealer has provided you with your FineArts Audion system in an assembled state, connected and ready for operation. If you want to change the settings yourself or look for new radio stations, please read the enclosed installation manual. The operating manual also describes the digital radio operation (Digital Audio Broadcasting) and illustrates the display options for this operating mode. DAB operation is only possible with an integrated DAB module (optional). 5 5 7 FineArts Audion The system operation of your HiFi Special features of your HiFi system 8 9 10 Packing contents/accessories Set-up and safety The wireless transmission system 11 11 12 13 15 Overview The HiFi system controls The back and bottom of the HiFi system The remote control The remote control menu system 2 CONTENTS __________________________________________________________________________________ 17 17 17 18 18 19 19 General functions Switching on Switching off Switching on from standby Selecting the input source Switching to standby Organising the HiFi system display 20 20 20 21 22 22 22 Volume and tone Adjusting the volume Adjusting the treble, bass, balance and fader Sound setting Switching loudness on and off Muting the HiFi system Setting up additional pairs of loudspeakers 23 23 23 25 26 FM mode Preparation Selecting radio stations Stereo/mono reception RDS reception 30 30 30 34 DAB mode Preparation Selecting DAB stations Additional functions in DAB mode ENGLISH 3 CONTENTS __________________________________________________________________________________ 37 37 37 38 41 42 44 CD mode General information about CDs Preparation Playing back a CD Selecting a CD track Additional functions Playing back tracks in a selected order ­ creating a track memory 48 49 49 49 50 Sleep timer mode Multi-room mode Operating pairs of speakers in additional rooms Switching the remote control to a pair of speakers in another room Setting up different input sources for individual rooms 51 51 52 61 63 64 Information Changing the remote control batteries Other remote control operating modes Rectifying minor problems Technical data GRUNDIG Service 4 FINE ARTS AUDION ________________________________________________ The system operation of your HiFi The following illustration shows you the options for multi-room operation of your HiFi system, and for operation in combination with other individual Grundig components. [. . . ] If the following measures do not bring about satisfactory results, please consult an authorised dealer. GENERAL PROBLEMS Problem Distorted or interfering signal in one or more of the loudspeakers during Tuner mode. Possible cause/remedy There is a radio-operated device being used in the immediate vicinity of the HiFi (e. g. Select a different transmission/reception channel. Position the antennas of the LSP3 and the HiFi system vertically. 15 minutes before you switch it on again. The HiFi system was switched onto standby with another installed remote control. Problems due to electrostatic discharge. Switch off the loudspeakers and the HiFi using the mains switch, then switch them on again. Check the mains plug and the mains switch of the loudspeakers (the operating indicator should be lit up green). Make sure the MUTING function is not activated. Check the location of the loudspeakers. The HiFi switches off. The HiFi system does not work. No sound. The left and right channels are inverted. The remote control does not work. 61 ENGLISH Change the batteries. The remote control has been deinstalled. INFORMATION __________________________________________________________________________ RADIO RECEPTION Problem No sound. Possible cause/remedy The MUTING function is activated due to poor stereo reception. Switch off FM STEREO to activate MONO reception, or manually adjust the frequency. Check antenna connection. Loud noise interference. DAB MODE Problem No DAB signal Possible cause/remedy Reposition the DAB antenna. CD MODE Problem The CD compartment will not close. Playback does not work. Possible cause/remedy The CD is not properly inserted. The CD is dirty, scratched or upside-down. A sudden temperature change has caused condensation on the laser lens system. This will dry off by itself after a short time. No disc is in the compartment, or the disc is dirty, scratched or warped. You are using a CD which does not adhere to the compact disc standard, or a CD-R or CD-RW which has not been burned correctly. Switch the function off. The message "NO DISC" is displayed. Playback does not start with the first track. MULTI-ROOM OPERATION Problem You can not select the input source you desire. Possible cause/remedy There are already two different input sources active. 62 INFORMATION __________________________________________________________________________ Technical data This device is noise-suppressed according to the applicable EC directives. This product fulfils the European directives 89/336/EEC, 73/23/ EEC and 93/68/EEC. [. . . ] INSTALLATION 10 In the »SETUP« menu, press » INSTALLATION«. ­ Display: the »INSTALLATION« menu. WT2 11 In the »INSTALLATION« menu, press » WT2«. ­ Display: the »WT2« menu. 54 INSTALLING THE WT2 MODULE _____________________________________________ 12 In the »WT2« menu, press » INSTALL WT2«. ­ Display: »PLEASE REFER TO THE INSTALLATION MANUAL«. INSTALL WT2 13 Press the »INSTALL« button on WT2 until the »INSTALL« indicator on the WT2 flashes orange. ­ This starts the installation of the WT2. When the orange »INSTALL« indicator on the WT2 switches off, the WT2 is installed on the HiFi. ­ The remote control display reads: »INSTALLATION OF WT2 COMPLETED«. EREO R INSTALL B 55 ENGLISH INFORMATION _____________________________________________________________ Setting the infrared code of the remote control to the television Because you can also use the HiFi remote control to operate the television, it is important to adapt the infrared code to the television you are operating. [. . . ]