User manual GRUNDIG P 37-730 TEXT/ICN

[. . . ] The , , , signs on the picture screen are symbols for the following buttons on the remote control handset: , = P- and P+ buttons (cursor movement up/down and function selection). , = ­ and + buttons (cursor movement to the left/right and function selection). In the following text, the illustrations of the buttons instead of the symbols will be shown. Safety and Installation 7 If the television is to be built into a compartment or similarly enclosed, minimum distances must be maintained (10 cm at the sides, 20 cm on the top). Assigning Programme Positions 1st possibility r 1 2 3 The Automatic Tuning System ATS This automatic tuning system scans the entire reception range and automatically stores all found programmes. How to proceed: Switch the TV set on from standby with one of the buttons 1. . . 9. [. . . ] AUX Call up programme data; hold down for 4 sec. to call up the ATS tuning system. v i 1 4 7 AUX 2 5 8 0/AV 3 6 9 TXT + ­ + ­ v i P+ ­ OK + P­ TP 711 r 1 2 Further functions Change b/w contrast: press i, OK, ­ , or + . Programme Sleep Timer (switch-off time 01. . . 99 min. ) : press i, OK, i and numeric buttons 1. . . 9. Press the i button to return to the TV programme. Automatic frequency fine tuning on/off: press i, OK, i, i, then select with ­ . Every changed value (volume, etc. ) is stored after approx. Pressing the OK button twice recovers the factory pre-settings. 3 !! The Remote Control Handset 9 " " » S « Only » BG « is possible. »DEC«If an encoded programme is assigned to this programme position and an appropriate descrambler (decoder) is connected, then select »ON«. »FT« If fine tuning is necessary after programme assignment, press the ­ button until the figures below FT get green. Press the P+ or P­ button until the best picture quality is obtained. Teletext Mode r r r Calling up Teletext: Press the TXT button. Select pages directly with the buttons 1. . . 9 (Available pages: 100 -899) Calling up the dialogue line: Press the AUX button. X /00 1 2 3 ?4 STOP 5 1 2 3 4 5 = Enlarge character hight. Select the function with the ­ or + button and call it up with OK. The functions 1, 3, 4, and 5 can be executed without calling up the dialogue line as follows: 1 3 4 5 i button. Directly call up subpages: Press the ­ i button. Enlarge character height: Press the + Reveal answer: Press the + Stop pages: Press the button. ­ button. r Selecting pages with the cursor (page catching) You can select pages without entering the page numbers. You can select the desired Teletext page in overview pages (pages containing three-digit page numbers). This function saves you entering the three-digit page numbers. 1 How to proceed: Press the P+ or P­ button. »Page Catching« appears on the bottom border of the picture. A rectangular cursor is flashing at the position of the fist or last page number in the overview page. Use the P+ or P­ button to move the cursor to the desired page number. The page appears on the picture screen. 2 3 10 r 1 Connection Connect the video recorder or satellite receiver with an AV cable to the AV socket at the back of the set. r 1 Operation of each connected device Starts video cassette recorder playback function or switches on satellite receiver. When connecting a decoder (descrambler), pay attention to the chapter on page 8: » Manual setting of program positions. [. . . ] If it is necessary to change the fuse in the non-rewireable plug, the correct type and rating (5 Amp ASTA or BSI approved BS 1362) must be used and the fuse cover must be refitted. If the fuse cover is lost or damaged the lead and plug must not be used until a replacement is obtained. Replacement fuse covers should be obtained from your dealer. If a non-rewireable plug or a rewireable 13 Amp (BS 1363) plug is used, it must be fitted with a 5 Amp ASTA or BSI approved BS 1362 fuse. [. . . ]