User manual GRUNDIG RS-SET 2

[. . . ] Should they be knocked over, fluid may spill on the electrical components, thus presenting a safety risk. MAINS 230V 50/60Hz VICE !SER RESET ! Do not open the loudspeaker casing under any circumstances. The manufacturer will not accept any liability for damage resulting from improper handling. Thunderstorms are a danger to all electrical devices. [. . . ] 1 Place the active loudspeakers in the room around the television; ­ or hang the loudspeaker by the recess on the back of the speakers on a screw which has been firmly anchored in the wall. MA IN S 230V 50/60Hz Note: We recommend using the RS-Set 2 active loudspeaker as the rear loudspeaker. The LSP2 active loudspeakers can then be used as the front loudspeakers. The rear loudspeakers should be placed at a sufficient distance and a suitable height to the left and right or behind the listener. When setting up the active loudspeakers, note that the minimum distance to the television is 50 cm. When setting up the active loudspeakers, make sure that they stand securely and are not affected by vibrations caused by resonance at high volumes. Three feet are attached to the bottom of each active loudspeaker to increase stability. If you hang the active loudspeakers to the wall you can remove the feet from the bottom. 14 OVERVIEW ________________________________________ The controls and connections for the RS-Set 2 Z Power switch, on the top of the device: switches the device on and off again. The loudspeaker is only fully disconnected from the mains after the plug has been pulled out. I Indicator Antenna. In the mains button: Flashing orange: installation phase 1 (sending identification); Flashing green: installation phase 2 (identification acknowledged); Continuous orange: the loudspeaker is in stand-by mode; Continuous green: the loudspeaker is in operation; Flashing green and red: reset mode ­ the loudspeakers have not been installed. This display changes to flashing orange after a few seconds (see Installation Phase 1). Flashing red: the protective circuit has been actuated. Note: If the protection circuit is actuated, switch off the loudspeaker using the »Z« button and let it cool down for at least 15 minutes. 15 ENGLISH OVERVIEW ______________________________________________ RESET Back of device: press briefly to start installation with WT2 manually; hold down (more than 10 seconds) to delete the stored installation settings (initial state). Back of device: connection socket for mains cable. Only for dealers for updating the device software. RESE T RESET 230 V 50/60 Hz MAIN S 230V 50/60Hz 16 CONNECTION AND OPERATION Connection and installation Connecting the mains cable _____________ 1 Plug the mains cable into the »230 V 50/60 Hz« socket on the back of the device. 2 Insert the power cord plug in the socket. MA INS 230V 50/60Hz 3 For instructions on how to install the loudspeakers with a WT2 transmitter please refer to the appropriate operating manual. Switching on and operating after installation 1 Switch on both loudspeakers with »Z«. ­ The orange indicators on the loudspeakers light up (stand-by). ­ The green indicators on the loudspeakers light up (operation). Note: The loudspeakers switch on or to stand-by mode automatically depending on control signals from the WT2. The change to stand-by function depends on the audio source and can take up to 30 minutes. 17 ENGLISH CONNECTION AND OPERATION ___________________________________________ Installing additional loudspeakers For installation when expanding the system (for example from two to four active loudspeakers), see the operating and installation instructions for WT2. Resetting the loudspeakers to the original state Note for dealers: With this function you can delete all existing installation data and reset the active loudspeakers to their original state. 1 When switched on, press » RESET« on the bottom of the device for longer than 10 seconds, using an implement such as a thin pencil. ­ The display flashes green and red. RESET Note: After the installation data has been deleted, the loudspeakers must be installed again. Reset mode is not required during operation and installation, and is therefore only available for specialist dealers. RESE T 18 INFORMATION _____________________________________________________________ These loudspeakers are noise-suppressed according to the applicable EC directives. [. . . ] If a non-rewireable 3-pin plug or a rewireable 13A (BS1363) 3-pin plug is used, it must be fitted with a 5A ASTA or BSI approved BS1362 fuse. If any other type of plug is used it must be protected by a 5A fuse either in the plug, or at the distribution board. If this type of plug becomes defective, ensure that the fuse is removed before disposal, to eliminate potential shock hazard. If it is necessary to change the fuse in the non-rewireable plug, the correct type and rating (5A ASTA or BSI approved BS1362) must be used and the fuse cover must be refitted. [. . . ]