User manual GTO PRO F310 KEYPAD

[. . . ] The recommended minimum distance between the gate and keypad is 10 ft. FCC WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Set the keypad DIP switches to match your entry transmitter's DIP switch settings. + 0 ­ 123456789 NOTE: If you have not changed your opener's transmitter code from the factory setting, see the "Setting Your Personal Transmitter Code" section in the gate openers manual then set the keypad DIP switches to match the new transmitter DIP switch setting. 1 GHI ABC 2 DEF 3 4 JKL 5 MNO 6 PRS 7 TUV 8 WXY 9 0 Step 2: Slide the keypad into the cover and secure with the small screws provided. Wired Installation of the Keypad NOTE: If you also plan to power the keypad with the gate opener's power source, run two pairs of wires as described below. One pair to hard-wire the keypad and the other pair to connect the keypad to the gate opener's battery. Step 1: Turn the gate opener's power switch OFF. Use 16 gauge, stranded, direct burial low voltage wire (part no. RB509) to connect the keypad to the opener control board. Run wire through PVC pipe from the ground to keypad and from the ground to the opener control board to protect the wire from lawn mowers or grazing animals. Determine how the wire will enter the keypad (i. e. from the back through a hole drilled in the mounting post or running the wire on the surface of the post). Remove the small rectangular knock-out on the back of the keypad cover and pull the wire into the cover. Then mount the cover to the post using the screws provided. Knock-out Step 2: To hard-wire the keypad - strip the wires back 3/16" and attach the wires to the terminal block marked RELAY OUTPUT on the keypad control board as shown to the right. Connect the other end to the opener's control board as shown in Control Board Connections section below. To wire the power supply to the keypad attach the wires to the AC/DC POWER IN terminal on the keypad control board as shown to the right. Connect the other end to the opener's battery - one end to the POSITIVE pole and the other to the NEGATIVE pole. Jumper OFF + 0 ­ 123456789 NOTE: For a hard-wired application the jumper between the two terminals on the keypad control board must be connected (ON) as shown. This will disable the 318 MHz RF transmitter. Step 3: Slide the keypad into the cover and secure with the small screws provided. 1 GHI ABC Jumper ON RELAY OUTPUT AC/DC POWER IN #1 #2 Power Supply from Opener Battery Hard-wire from Gate Opener 2 DEF 3 4 JKL 5 MNO 6 PRS 7 TUV 8 WXY 9 0 Step 4: With the power to the opener turned OFF. Remove opener control board cover and feed enough of the low voltage keypad wire through a strain relief to reach the gate opener control board terminals. Step 5: Attach the wires from the keypad to the opener control board terminal blocks as shown below. Step 6: Replace the control board cover and turn the power switch ON. Step 7: Program your `Personal Master Code' and any additional entry codes (for a total of 25 entry codes) you wish. See Programming the Keypad section. Control Board Connections NOTE: If your control board doesn't look like any of these diagrams, please call GTO Technical Service at 1-800-543-1236 or 850-575-4144 for additional support. Mighty Mule 250 E-Z Gate Opener Control Board 15 AMP 18 VAC INPUT SET CLOSE LIMIT Mighty Mule 350 Control Board LINK GRN BLK RECR SAFETY COMMON EXIT EDGE CYCLE RED Connect #1 wire from the RELAY OUTPUT terminals on the keypad to CYCLE terminal on the gate opener control board. #1 #2 CYCLE CLOSE CLOSE EDGE EXIT/ OPEN OPEN EDGE COM COM SHADOW LOOP SAFETY GTO/PRO DC Powered PRO-SW3000 and PRO-SW4000 Control Boards J11 SAFETY CYCLE CLOSE SHADOW LOOP CLOSE EDGE EXIT OPEN OPEN EDGE Connect #2 wire from the RELAY OUTPUT terminals on the keypad to the COM terminal on the gate opener control board. GREEN LEARN TRANSMITTER BLK RADIO RED COM COM SAFETY EDGE Connect #1 wire from the RELAY OUTPUT terminals on the keypad to CYCLE terminal on the gate opener control board. #2 #1 CYCLE COMMON Connect #2 wire from the RELAY OUTPUT terminals on the keypad to the COMMON terminal on the gate opener control board. Connect #1 wire from the RELAY OUTPUT terminals on the keypad to CYCLE terminal on the gate opener control board. Connect #2 wire from the RELAY OUTPUT terminals on the keypad to the COMMMON terminal on the gate opener control board. [. . . ] · 3121 Hartsfield Road · Tallahassee, Florida 32303 Telephone (850) 575-0176 · Fax (850) 575-8912 · website www. gtoinc. com The contents of all material available on this installation manual are copyrighted by GTO, Inc. ("GTO"), unless otherwise indicated. All rights are reserved by GTO, and content may not be reproduced, downloaded, disseminated, published, or transferred in any form or by any means, except with the prior, written permission of GTO. Any reprinting of GTO publications is by permission only. [. . . ]