User manual GTO PRO LIGHT KIT

[. . . ] IMPORTANT: 16 gauge, multi-stranded, direct burial, low voltage wire (RB509) is required to connect the lights to the digital control board (see diagram on page 1). Small sections of the same wire will also be required for connecting light kit control board to gate operator control board and power source. Please read manual to determine how much wire you will need. Gate Opener Light Kit with Digital Controller Parts Included: 1 2 3 3 4 4 5 5 6 7 7 14 x2 0 60 DELAY TIMER 1 8 2 9 10 Face Mount Post Mount 11 12 6 13 15 16 1. Glue (1) · Digital Controller: Controls lights to conserve battery life. [. . . ] When you are satisfied with the placement of the fixtures, glue the lens support pieces using a small amount of glue (provided). Be careful to keep the glue off the outside of the support pieces. See Figure12. Figure 11 Figure 12 Use small amount of glue to secure lens support assembly 3 Installing the Photocell and Control Board Installing the photocell and low voltage wire strain relief: 1. Use a screwdriver to remove a "knockout" in the bottom of the gate operator control box or a weatherproof junction box. If knockouts are not available, carefully drill a 5/8" hole, then install the photocell as shown in Figure 13. In another knockout or 5/8" hole, install the strain relief provided. Run the low voltage wire from the lights through the strain relief into the box. Secure by tightening the strain relief nut until the wire is snug. Always run wire from the ground to the box in PVC conduit to protect it from grazing animals and weed eaters. Figure 13 Photocell Wiring the Light Kit Installing the Photocell: Place the Light Kit control board in the gate operator control box or a weatherproof junction box. Connect the Light Kit control board using Figure 15 and the Wiring Diagrams on the following pages. Plug the Light Kit's Wiring Plug to the Lgiht Kit control board. Connect the two RED wires from the lights to one of the Light Kit control board terminals. Connect the two BLACK wires from the lights to another Light Kit control board terminal. IMPORTANT: Only use the two terminals shown in Figure 15 to connect the wires from the lights. Figure 14 Low Voltage Wire from Lights PVC Conduit NOTE: Included in the light kit are four wire splicing locks. They are used to connect the end of one wire to the middle of another. With wires in place, fold locking tab over and press until it locks in place. Make sure the locks are clamped securly to the wires. See Figure 16. Light Kit Control Board x2 0 6 60 DELAY TIMER AY AY AY TIME AY TIME AY TIME AY TIME Potentiometer for Adjusting the Light Duration Delay Low Voltage Wires from Lights Wiring PLUG BLUE Wires WHITE Wires Figure 15 RED Wire BLACK Wire Figure 16 4 Connecting Light Kit to Mighty Mule FM500/502, GTO/PRO SW2500, SW3000, and SW4000 Gate Openers: 1. Connect the other end of the JUMPER wire to the RED gate opener battery lead using the wire splicing locks provided. Connect the BLACK wire from the Light Kit control board to the GRN ACCESSORY terminal on the gate operator control board. Connect two BLUE wires from the Light Kit control board to the RED OPERATOR terminal and and two BLUE wires to the BLK OPERATOR terminal on the gate opener control board. [. . . ] gate opener accessories are warranted by the manufacturer against defects in workmanship for a period of one (1) year from the date of purchase, provided recommended installation procedures have been followed. In the case of product failure due to defective material or manufacturer workmanship within the one (1) year warranty period, the accessory will be repaired or replaced (at the manufacturer's option) at no charge to the customer, if returned freight prepaid to GTO, Inc. , 3121 Hartsfield Rd. , Tallahassee, FL 32303. IMPORTANT: Call 850/575-4144 or fax 850/575-8950 for a Return Goods Authorization (RGA) number before returning goods to factory. Products received at the factory without an RGA will not be accepted. [. . . ]