User manual GTO PRO-SW 1000SERIES

[. . . ] Installation Manual for the ¨ + LIS TED 75 Series Automatic Gate Operator for Vehicular Swing Gates WARNING! READ ALL INSTRUCTIONS CAREFULLY AND COMPLETELY before attempting to install and use this automatic gate operator. This gate operator produces a high level of force. Stay clear of the unit while it is operating and exercise caution at all times. , INC. 3121 Hartsfield Road · Tallahassee, Florida, USA 32303 Telephone (800) 543-GATE or (850) 575-0176 · Fax (850) 575-8912 · www. gtoinc. com © 2000 GTO, Inc. RB918 rev-04/22/02 This product meets and exceeds the requirements of UL 325, the standard which regulates gate operator safety, as established and made effective March 1, 2000, by Underwriters Laboratories Inc. GTO/PRO 1000 series automatic gate operators are intended for use with vehicular swing gates. These operators can be used in Class I, Class II and Class III applications. [. . . ] If your gate type matches this configuration, you DO NOT need to adjust the DIP switches; proceed to the Potentiometers section on the next page. NOTE: To change the DIP switch settings, you must turn the control box power switch OFF; move the switch; then turn the power back ON. Use a small screwdriver to move the switches. PULL/PUSH: Set to PULL for swing gates that pull-to-open [factory setting]; PUSH for swing gates that push-to-open (see Push to Open Installation on pages 30-31). NOTE: The direction a gate opens is determined by standing inside the property and facing toward the gate. SNGL/DUAL: Set to SNGL for a single gate leaf [factory setting]; DUAL for dual gate leaves. SEQ1: Controls the opening order of dual gate leaves. See Setting the Control Board for Dual Gate Installations on page 39 for more information. SEQ2: Controls the opening order of dual gate leaves. See Setting the Control Board for Dual Gate Installations on page 39 for more information. S DIP switches OBSTRUCT SENS. PULL/PUSH SNGL/DUAL SEQ1 SEQ2 4 ON 1 2 3 MIN MAX LEARN AUTOC 60 STATUS LOSE + BATT ­ 120 OFF INERTIA MAX MIN UCT OBSTRS. SEN MAX USH PULL/P L UA SNGL/D EQ1 S SEQ2 MIN LEARN G RB OPN EDG CLS EDG OPN EDG CLS EDG ORG BLU GRN RED BLK ORG BLU GRN GRN ORG BLU WHT BLK RED SOLAR 18VAC ­ + ~ ~ SECO FIRST POWE R IN ND O TOR PERA ALAR M ACCE SSOR Y RCVR OPER ATOR 23 Potentiometers The three (3) potentiometers on the control board operate like a volume control on a radio. They control the auto close timer, inertia, and obstruction sensitivity of the operator. Use a small slotted screwdriver to turn the arrow in the center of the potentiometer. Clockwise rotation increases the setting (MAX). Counterclockwise rotation decreases the setting (MIN). AUTO CLOSE (auto close timer): Determines how long the gate will remain open before it automatically closes. INERTIA: Fine tunes obstruction sensitivity in the opening and closing modes. INERTIA allows the operator to attempt to push an obstruction clear of the gate path. When INERTIA is set to MIN the operator will obstruct quickly (i. e, . will attempt to push an obstruction briefly); when set to MAX, the operator will obstruct slowly (will attempt to push against an obstruct for a longer period). (obstruction sensitivity): Determines the amount of force exerted by the gate on an obstruction before the operator stops and reverses. [. . . ] The kit comes with the battery and wiring harness for easy installation. Battery life 3 to 5 years. GTO NEMA Box (FM317) GTO's NEMA 4X rated weatherproof box is large enough (14" W x 6" D x 16" H) to accommodate all add-on items necessary for custom gate operator installations. It is made of fire retardant ABS plastic and comes with a heavy duty 14 gauge steel backing plate for mounting accessories. The unique, lockable cover (use the Master® Pin lock RB975 for added security) can be completely removed for easier access during installation and service. [. . . ]