User manual GTO PRO-SW 3000XL MASTER

[. . . ] Installation Manual for the DC-SERIES ® DC-SERIES ! ® WARNING Can Cause Injury or Death MOVING GATE 1-800-543-GATE (4283) · www. gtopro. com SINGLE Gate Operator System FOR PROFESSIONAL INSTALLATION ONLY! WARNING! This equipment is similar to other gate or door equipment and meets or exceeds Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has hazards associated with its use and therefore by installing this product the installer and user accept full responsibility for following and noting the installation and safety instructions. Failure to follow installation and safety instructions can result in hazards developing due to improper assembly. You agree to properly install this product and that if you fail to do so GTO, Inc. [. . . ] The ON/OFF Switch is located on the bottom of the control box. Remove the control box cover and slide the battery into position with its terminals to the RIGHT (see illustration). Connect the BLACK battery wire to the NEGATIVE (­) battery terminal. Connect the RED battery wire to the POSITIVE (+) terminal. Pay close attention to the color of the wires. If the wires are connected incorrectly, the control board may be damaged. NEVER insert the battery with the terminals to the left. BLACK wire to NEGATIVE (--) terminal RED wire to POSITIVE (+) terminal BLACK RED 12 V Battery (Included) Step 15 Strip approximately 3/16" of insulation from each wire of the operator power cable. Twist each exposed wire tightly (there are seven [7] wires inside the power cable sheath). Loosen sealing nut on strain relief hub at bottom of control box. Insert power cable into control box through strain relief. Thread approximately 6" of the power cable into the control box and retighten sealing nut until the power cable locks into place. 15 FUSE SWITCH GTO, Inc. 3121 Hartsfield Rd Tallahassee, FL 32303 ALARM BAT­ BAT+ 800-543-GATE www. gtoinc. com 1234 DUAL ON MODES 1 2 3 4 ON OFF SET LIMIT MODES ON 1 1 2 3 4 5 6 7 ON 2 3 4 5 6 7 OFF LEARN TRANSMITTER SWITCH 10' 12' 14' 8' GATE LENGTH 16' ~~ 18VAC ­ + NC RLY-COM NO SOLAR RELAY OUT SHADOW LOOP SAFETY CYCLE CLOSE EXIT/ OPEN SLAVE INPUTS MASTER INPUTS OPEN EDGE GRN WHT BLUE BRN ORG RED BLK GRN WHT BLUE BRN ORG RED BLK COM COM CLOSE EDGE GRN BLK RED RECEIVER Strain Relief Lock Nut Hub SWITCH Sealing Nut Strain Relief GRN WHT BLUE BRN ORG Operator Power Cable J13 MASTER INPUTS Step 16 Insert the stripped operator power cable wires into the appropriate terminals on the OPERATOR terminal block. The green wire should be inserted into the GRN terminal, the blue wire into BLU, the orange wire into ORG, black wire into BLK, and the red wire into the RED terminal. Tighten the set screws against the end of the wires. A dab of petroleum jelly on each terminal will help prevent corrosion. Do not overtighten. RED J5 BLK Power cable from operator (master) arm CYCLE CLOSE SAFETY EXIT OPEN SHADOW LOOP CLOSE EDGE OPEN EDGE COM COM GRN J11 J8 MIN STALL FORCE RECEIVER Correct Wrong Wrong J12 Wire Terminal Block Wire Terminal Block Wire Terminal Block 18 MAX BLK RED Powering the System Installation of the Transformer IMPORTANT: · The transformer is designed and intended for indoor use. If the transformer can be plugged only into an outside electrical outlet, a weatherproof cover or housing (available at local electrical supply stores) must be used. All low voltage wire used with the GTO/PRO® 3000 Gate Operator must be 16 gauge dual conductor, multi-stranded, direct burial wire (see page 20) and the Accessory Catalog). from an ac power source, you will need to use at least one 5 watt Solar Panel to charge the battery (see Accessory Catalog). Refer to the Solar Panels and Gate Activity chart below. · · Optional Solar Panels and Gate Activity The table and map illustrate the maximum number of gate cycles to expect per day in a particular area when using from 5 to 30 watts of solar charging power. The figures shown are for winter (minimum sunlight) and do not account for the use of any accessory items. Accessories connected to your system will draw additional power from the battery. [. . . ] Wired installations require 16 gauge, low voltage, multi-stranded, dual conductor, direct burial wire (sold separately). Requires 3 AA batteries (not included). GTO/PRO Exit Wand (FM139) The GTO/PRO® Exit Wand is designed for residential and agricultural applications and is compatible with all GTO/PRO® automatic gate operator models. The wand is an electromagnetic sensor, which offers 'hands free' operation of the GTO/PRO® 3200 Gate Operator with a 12 ft. radius of detection of vehicles in motion. Automatic Gate Lock Pull-to-Open (FM144) ELE CTR ON IC MAT ® CK AUTO LOLOCK GATE ITY UR SEC IC A MUST for added security. [. . . ]