Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HAFLER XL-280. We hope that this HAFLER XL-280 user guide will be useful to you.
Lastmanuals help download the user guide HAFLER XL-280.
Detailed instructions for use are in the User's Guide.
[. . . ] 10 DESIGN FEATURES SR2300CE, SR2800CE . . 20 SERVICE POLICY AND LIMITED WARRANTY . . 21
1
NOTICE - IMPORTANT SAFETY INFORMATION
The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure, that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. [. . . ] Normal operation will continue immediately after the short is removed. Power Supply Current Limiting protection- The switching power supply will protect itself from excessive power dissipation by continuously monitoring currents in the switching MOSFETs. The Current Limiting circuit measures the currents in the switching MOSFETs and will instantly limit them to a safe level. Soft turn-on/fast turn-off - Speaker loads are protected from turn-on/turn-off transients by a circuit that monitors the power supply, and controls the amplifier when power on/off events are detected. At turn-on, this circuit waits for power supply voltages to settle, then sends a turn-on ramp signal to slowly turn the amplifier on. At turn-off, this circuit acts quickly to turn off the amplifier before power supply capacitors discharge, and voltages collapse into the output signal - causing speaker "pops".
9
Design Features SR2300, SR2800
FRONT VIEW
REAR VIEW
3
+
1 2
+
600W 2 8
®
S R 2 8 0 0 Made in the U. S. A.
A Division of Rockford Corp. Tempe, AZ 85281
Audio GND
Chassis CH A IN CH A OUT Float
700 W Stereo, 2 8 1400W Mono,
BIAMP STEREO
1200W 4 16 Mono, 70V, 100V
For 70V, 100V, or Mono · Use CH B input · Load across RED terminals · Set load switches to one Class 2 wiring
CH B IN (Mono) CH B OUT
+
+ +
600W 2 8
Attention: Utiliser un fusible de rechange de même type. CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.
250V T15A 100V-120V~
50/60Hz
460W
1. Recessed Front Panel - Prevents switches and controls from accidentally being adjusted or broken. Power Switch - Turns the amplifier ON and OFF 3. Power LEDs - Verifies that the amplifier channel is ON 4. Mains Power Connector - Connects AC Voltage to the amplifier. The power connector is safety approved IEC type 320. The earth (safety) ground pin of the power connector is permanently connected to the chassis. This connection is capable of shunting in excess of 30A of fault current. Biamp/Stereo Switch - This dual purpose switch selects either standard 2-channel stereo mode or 1-channel in, 2 channels out Biamp mode. Turn amplifier off before operating this switch. Removable Rear Panel - 8 screws can be removed to service fans and internal components without unracking the amplifier.
10
Design Features SR2300CE, SR2800CE
FRONT VIEW
REAR VIEW
PIN 1+ 12+ 2SPKR CHA+ CHACHB+ CHBAudio GND
600W 2 8
®
S R 2 8 0 0 Made in the U. S. A.
A Division of Rockford Corp. Tempe, AZ 85281
700 W Stereo, 2 8 1400W Mono,
CH A IN
BIAMP
CH A STEREO BUFFER THRU
Chassis PIN 1+ 12+ 2SPKR NC NC CHB+ CHB-
Float
CH A OUT (MONO)
Attention: Utiliser un fusible de rechange de même type.
600W 2 8
CAUTION: For continued protection from risk of fire, replace only with same type and rating of fuse.
CH B IN
CH B Class 2 wiring BUFFER Class 1 wiring THRU must be used in Mono
For 70V, 100V, or Mono CH B · Use CH B input · Load across RED terminals · Set load switches to one half load impedance
250V T15A 100V-120V~
50/60Hz
460W
1. Recessed Front Panel - Prevents switches and controls from accidentally being adjusted or broken. Power Switch - Turns the amplifier ON and OFF 3. Power LEDs - Verifies that the amplifier channel is ON 4. [. . . ] (1400WSR2800, 700WSR2300) CE units: Wire SPEAKON as shown above and connect to CH A output. CH B input sensitivity controls 70V mono output level. Amplifier will clip at 70Vrms level.
19
100V MONO MODE (SR2300/SR2800)
Load
100V 70V 8 4 2
Power
100V 70V 8 4 2
100V
70V
100V
70V
CE SPEAKON Connector Wiring
A Division of Rockford Corp. Tempe, AZ 85281
SR2300
3
SR2800
+
1 2
+
300W 2 8
S R 2 3 0 0 Made in the U. S. A.
Audio GND
Chassis CH A IN CH A 600W 4 16 Mono, 70V, 100V Float
300 W Stereo, 2 8 600W Mono, 70V, 100V
BIAMP STEREO OUT
+
+ +
300W 2 8
Attention: Utiliser un fusible de rechange de même type. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE HAFLER XL-280
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HAFLER XL-280 will begin.