User manual HAICOM HI-406BT

[. . . ] HI-406BT Bluetooth GPS receiver 1 Table of Contents 1. 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. 2 Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] With HI-406BT, your mobile devices, such as, Smartphone, PocketPC, laptopPC, tabletPC, etc. can receive GPS data wirelessly and perform the GPS applications, such as, car navigation, personal navigation, route planning, tracking, etc. Equipped with the most powerful and ultra high sensitive SiRF StarIII chip set, HI-406BT can get the 3D fix in very short time and under poor reception environment, such as in the middle of the car, next to the tall building, in your backpack, or pocket. 3 1. 2 Main Features: · 20 Channels "All-In-View" Tracking · Position accuracy of 10 meters 2D RMS · Cold/Warm/Hot Start Time: 42/38/1 Seconds (Signal Strength > 30 dB-HZ) · Reacquisition Time: 0. 1 seconds · Support Standard NMEA-0183 at 19200 bps baud rate (Defined by customer 4800 up to 57600) · Support Power Saving Mode · Compatible with Bluetooth devices with Serial Port Profile (SPP) · Superior Sensitivity for Urban Canyon and Foliage Environment · Ultra small, sleek, and lightweight design easily fits in your hand · Li-polymer battery lasts for more than 8 hours of use in connection 4 2. 1 Setting up: Bluetooth GPS receiver STEP 1: Open the battery cap and put the battery (406-BTT) into the battery compartment. Push down and pull out 5 STEP 2 Connect the AC charger to home electronics outlet or connect the inclusive DC charger to the car cigarette lighter. As soon as they connected, the solid amber light on the right side in front of HI-406BT will turned on (stay on) meaning the battery charging. AC charger to home electronic outlet DC charger to car cigarette lighter (DC 12V~24V) Mini-1394 MMCX external antenna plug female connector for power in and GPS signal out 6 STEP 3 As soon as the battery fully charged, the amber light will turned off, then, unplug the charger. Indicator for power charging and GPS status Indicator for battery low (Red) and Bluetooth status (Blue) 7 STEP 4 There is switch on side of HI-406BT. The switch on the right side is for Bluetooth GPS receiver. As soon as turn on the switch on the side, the GPS receiver will start to function and search the satellites. Meanwhile, the LED indicator on the right side in front of HI-406BT will turned green (stay on - the GPS receiver not get 3D fixed yet) Please make sure place the HI-406BT outdoor open space so that it can get the proper satellite signal. After HI-406BT gets enough satellite data (lock more than 4 satellites), HI-406BT is in 3D fixed and the green light start blinking. 8 Bluetooth GPS Switch LED indicator color Amber LED off Green (blinking) Green (Stay on) Blue (blinking) Blue (stay on) Red Status HI-406BT battery charging HI-406BT battery fully charged GPS in 3D fixed GPS searching more satellite and not in 3D fixed yet Bluetooth searching host device Bluetooth paired and connected HI-406BT battery low 9 STEP 5: As soon as turn on the switch on the right side, the Bluetooth will also start to function and searching. The blue light on the left side in front of HI-406BT will turned on (Blinking) meaning the Bluetooth is searching the host device and not get paired yet. Please consult the Bluetooth step by step connection guide from this manual on section. The pin code is " 0000 " when asked the pin code. [. . . ] Data rate Transmission Power (Maximum) Hoping Receiving Signal Range Receiver IF Frequency Baseband Crystal OSC Compliant 2400MHz to 2483. 5MHz GFSK, 1Mbps, 0. 5BT Gaussian Asynchronous: 723. 2kbps/57. 6kbps Synchronous: 433. 9kbps/433. 9kbps 4dBm(Class 2) 1600hops/sec, 1MHz channel space -84 to -15dBm 1. 5MHZ center frequency 16MHz Bluetooth Specification v1. 1 Electrical Main power input Power consumption Backup Power Operation time 5±5%VDC 0. 4W @ 3. 3VDC (Full Power) 1. 5±10%VDC input 8 hours (1000mAh Li-Ion battery) 20 GPS Firmware Protocol Baud Rate Update Rate Datum NMEA/SiRF Binary 19200 bps 1Hz WGS84 Environmental Temperature Operating Temperature 10°C to +55°C Storage Temperature 20°C to +65°C Relative Humidity 5% to 95%, non-condensing LED Indicator LED 1 Color Blue Flashing Blue Red BT Active Yes No Low Power Yes LED 2 Color Green Flashing Green Orange GPS Fix Status No Yes Battery Charging Yes 21 6. Get Connected; Installation Guide 6. 1 Laptop PC Installations Run "My Bluetooth Places" and Double Click the "Find Bluetooth Devices " icon Double Click "HI-406BT" 22 Double Click "GPS OUTPUT on HI-406BT" 23 Key in pin code: "0000" Connected 24 6. 2 PDA Installations Double Click the Bluetooth icon 25 Double click "HI-406BT" 26 Key in pin code: "0000" Found the host device 27 For Connected with device Select the correct com port 28 Start GPS, NMEA message inflow More satellites info 29 30 [. . . ]