User manual HAIER 3HUM20H03-R2

[. . . ] FLOOR UNIT ROOM AIR CONDITIONER OPERATION MANUAL Please read this operation manual before using the air conditioner. No. 0010509578 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in an air conditioner can be recycled . Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. [. . . ] Confirmation indicator: After pressing power ON/OFF, if no display, reload the batteries. Note: Full display or unclear display during operation indicates the batteries have been used up. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under displayed wind speed When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 10 Operation DRY Operation 1. Unit start Press ON/OFF on the indoor unit, or press ON/OFFon the remote controller, unit starts. Previous operation status appears on LCD display (no timer and sleep). Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select DRY operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting o increase 1 C, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting o decrease 1 C, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. COOL operation starts when room temp. is higher than temp. setting. 5. Unit stop Ultra-low air flow Press ON/OFF button, the unit stops. Temp. setting+2oC Temp. setting On reaching temp. setting +2oC unit will run in mild DRY mode. 11 Operation FAN Operation 1. Unit start Remote controller Press ON/OFF on the indoor unit, or press ON/OFFon the remote controller, unit starts. Previous operation status appears on LCD display (no timer and sleep). 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation 3. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI 4. Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode. In FAN mode, SLEEP operation is not available. 12 Operation HEAT Operation Remote controller 1. Unit start Press ON/OFF on the indoor unit, or press ON/OFFon the remote controller, unit starts. Previous operation status appears on LCD display (no timer and sleep). 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select HEAT operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting o increase 1 C, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting o decrease 1 C, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Regarding the ambient temperature display during the heating operation In defrosting, the indoor temperature value displayed may be reduced due to the dropping of cooling air of the evaporator of indoor unit under cooling mode. It is normal phenomenon. Air conditioner is running under displayed wind speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 13 Operation Adjusting the Air Flow Direction You can adjust the air flow direction to increase your comfort Notes on flap angles When SWING is selected, the flap swinging range depends on the operation mode. (See the figure. ) Adjusting the flap COOL/DRY HEAT NOTE Unless [SWING] is selected, you should set the flap at a near-horizontal angle in HEAT mode and at a upward position in COOL or DRY mode to obtain the best performance. CAUTION Do not try to adjust the flap by hand. When adjusting by hand, the mechanism may not operate properly or condensation may drip from air outlets ATTENTION When adjusting the flap by hand, turn off the unit, and use the remote controller to restart the unit. Adjusting the louver Hold the knob and move the louver. [. . . ] If it is too dirt, clean with detergent or neutral soap water. Rinsing with fresh water, dry the filter and re-assemble. Caution: o Do not wash filter in hot water above 40 C, which will damage the filter. Clean the indoor(outdoor) unit Clean with warm cloth or neutral detergent, then wipe away moisture with dry cloth. Do o not use too hot water(above 40 C), which will cause discoloration or deformation. [. . . ]