User manual HAIER 50FREE-3

[. . . ] Fully Automatic Washing Machine User's manual This manual is for 50FREE-3 Please read this manual carefully before using. Retain it for future reference. Packing list Contents Names of the parts 1 Safety precautions 2 Installation and adjustment 4 Install the water inlet hose 6 Preparation before washing 8 Put in the laundries 8 Add the detergent 9 Use the operation buttons 10 Close the top lid 14 Washing finished 14 Disposal after washing 15 Trouble shooting Answer to question 16 Packing list 17 Specification table the cover 2 User's manual Warranty card The side of connection between the water inlet hose and the washing machine Quantity One One One The side of connection between the jointer of the water inlet hose and the water faucet Tapping screws Eight Bottom plate One Between the upper cushion of the washing machine package and the upper seal of the package carton Inner cover component One Inside in inner tub of washing machine Automatic washing machine One Specification Water level/Water quantity (about) Water level/Water quantity (about) Max water consumption Injection pressure Rated washing spinning capacity Rated washing / / spinning capacity High/33L, Medium/22L, 4/32L 1/16L 2/21L 3/26L Low/14L 0. 03Mpa-0. 78Mpa 0. 03Mpa-1Mpa 3. 0kg (weight of standard dry cloth) 3. 3kg (weight of standard dry cloth) 17 Trouble-shooting answer to question (If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special maintenance department or after-sale service department of our company. [. . . ] It is suggested to use low-foaming washing powder Dismantle Install 14 3 Installation and adjustment Please install and adjust the machine according to the requirement of the manual. It is very important to your security and correct operating the machine. After switching on the power, the washing machine will set to common program including"wash, rinse, spin "automatically. To select other procedures, push the " WASH", " RINSE"or "SPIN"button to select the time of wash and spin, and the times of rinse. After switching on the power, if you push one of the button among "RINSE"and"SPIN the digitron of the former procedures will turn off automatically. For instance: after switchingon the power. If you push the "SPIN" button first, it will execute spin singly after starting. Install the inner cover 1. Open the top lid of the washing machine. 2. Put the inner cover component on the outer tub cover, aiming the inner cover shaft to the installation hole of the corresponding outer tub cover shaft groove. 3. Firstly insert the inner cover shaft of I side into the correspon -ding outer tub cover shaft groove, then push the another inner cover shaft into the corresponding outer tub cover shaft groove. Section · enlarging Please install to designated position to guarantee there are no dropping or abnormal sound in opening and closing of the inner cover, and the operation shall be smooth. Do not dismount the Push inner cover component after washing. Outer tub cover shaft groove Inner cover shaft Outer tub cover Inner cover Attention Even there's no water in the tub, a certain period is required before spin starting. Separate the laundries that are not colorfast from other laundries in washing. Do not use the HEAVY program for the woollen textiles. The pulsator will not rotate unless the water is filled to water level . After the machine starts operation, you can set the program and procedure during washing, set spinning time during rinsing but can not make setting in other cases. Install the bottom plate After you open the package, please lean the washing machine gently down on soft items ( like the towel cloth, blanket, etc. Install the bottom plate to the bottom of the machine with the eight screws by a cross screwdriver, then lift the machine up gently. 2. Do not trample or press the drain hose. 2 Push the PROGRAM SELECTION button to select the suitable automatic program PROGRAM After switching on the power, the machine will set to STANDARD program automatically. To select other program, push the PROGRAM SELECTION button till the corresponding indicator is on. Refer to the PROGRAM SELECTION button in Page 11. For example: select SAVE WASH for the quick washing of QUICK wash Page11 the laundries with light dirt. 4. If extra drain hose is needed, please make separate purchase. The inner diameter of the extra hose shall not less than 26mm, and the length shall not exceed 1. 5m. 3 Push WASH RINSE suitable programs SPIN button to select POWER ON/OFF MIN START PAUSE If the drain hose is too long, cut it at mid point. To make smooth drainage, cut the front end of the hose slantingly. If the extra hose is too long, cut it either at A or at B point. 12 5 Install the water inlet hose Power On/Off button Wash remain time indicator digitron The program is selected but not on, It displays the total minutes of the program During operation of programs, it displays the remained time (minute). In case of abnormal phenomenon, it displays the abnormal symbol (see to Page 16) Page 16 1. Attach the water inlet hoses to the water faucet. [. . . ] The instant dissolving of the washing powder: 1. Prepare warm water of 30 C and a container. 2. Add the powder while stirring to fully dissolve it. The powder is more prone to pollute the laundries than the detergent. Therefore please use it with proper quantity. [. . . ]