User manual HAIER ADP 8352

[. . . ] 12 Months Guarantee 18 DIPLOMAT most from your Fully Integrated Dishwasher GUARANTEE CONDITIONS (a) Any claim during the period of the guarantee MUST BE ACCOMPANIED WITH THE RECEIPT relating to the original purchase. (b) The unit must be correctly installed and operated in accordance with the manufacturer's instructions and used for normal domestic purposes. (c) The guarantee does not cover accidental damage, misuse or alterations which are likely to affect the units. (d) The guarantee is invalid if the unit is tampered with, or repaired by any unauthorised person. [. . . ] Cleaning the Water Inlet Filter Periodically clean the water inlet filter (see figure) located on the outlet of the water supply tap. After turning off the water tap, unscrew the end of the water supply hose, remove the filter 'A' and clean carefully under running water. Then, return the filter to its place and tighten the water supply hose back into position. Stage 2 Connect the water, drain and electrical supplies (230 - 240V, 50Hz, 13A). To remove spots or stains from the surface of the interior, use a cloth dampened with water and a little white vinegar, or cleaning product made specifically for dishwashers. When You Go on Holiday: It is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly open. This will help the seals last longer and prevent odours from forming within the appliance. Seals One of the factors that cause odours to form in the dishwasher is food that remains trapped in the seals. Periodic cleaning with a damp sponge will prevent this from occurring. Stage 6 The dishwasher should now be screwed to the underside of the worktop, via the two fixing holes in the top trim Stage 7 Cut clearance in the plinth to allow the door to open fully and seal edges with a suitable varnish to prevent water ingress. Starting the Wash Program (cont. ) 1 2 3 4 12 Know Your Dishwasher WARNING: After loading, ensure that both spray arms are free to rotate. We cannot accept responsibility for damage caused by incorrect loading. 5 6h 4h 2h ADP8352 1. 5 67 8 9 Upper Basket Spray Upper Basket Upper Basket Adjustment Height 1 2. 3. 2 3 4 5 Setting The Start Delay Time Open the door of the dishwasher partially. Turn on the appliance by pressing the ONOFF button '3'. The start time for the wash cycle can be delayed for 2, 4 or 6 hours. Each time the delay button '9' is pressed, the delay indicator light '8' will come on indicating the length of the delay. After selecting the delay time, the wash cycle can be set, as explained in "Starting a wash cycle. . . " There will be a short beep, and at this point the delay period will begin to count down. During this period the delay indicator light '8' will blink. At the end of the delay time, the indicator will stop blinking and the cycle will start. NOTE: a) During the delay period, none of the settings can be modified. If necessary, they can be cancelled by pressing programme selector '5' for about 5 seconds. b) If the power to the appliance goes off or the door is opened during the delay period, the clock will stop the countdown. It will start again when the power has come back on, or when the door has been closed. 4. 9. Upper Basket Spray Arm Lower Basket Filters Detergent Dispenser and Rinse Aid Container Salt Container Lower Basket Spray Arm 9 6 8 7 Control Panel Description 1 2 3 4 1/2 Load Button This option makes it possible to wash dishes using only the upper rack, if there are not enough dishes for a full load, This will allow you to save on water and electricity, however, it cannot be used with the heavy duty wash cycles. Set the desired programme and the delay option if required, then press the 1/2 Load Button '2'. [. . . ] Allow 15 minutes for the washing activity to subside and to allow the crockery to cool down to a safe temperature. The dishwasher is designed to allow for adjusting the amount of salt consumed based on the hardness of the water used. This is intended to optimize the rate of salt consumption. To adjust salt consumption, proceed as follows: - Unscrew the cap from the salt container; - There is a ring on the container with an arrow on it (see figure to the side), - If necessary, rotate the ring in an anticlockwise direction from the "-" setting towards the "+" sign, based on the hardness for your area. It is recommended that adjustments be made in accordance with the following table: Water Hardness Clarke degrees 0 - 14 14 - 36 36 - 71 71+ Selector position * mid + °dH 0 - 17 18 - 44 45 - 89 89+ mmol/l 0 - 1. 7 1. 8 - 4. 4 4. 5 - 8. 9 8. 9+ Detergent and Rinse Aid Dispenser Detergent It is recommended that powder detergent, not tablets, specifically intended for use with dishwashers should be used. [. . . ]