User manual HAIER AS12GS1ERA

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL Contents AS07GS1ERA AS09GS1ERA AS12GS1ERA PARTS AND FUNCTIONS OPERATION INDOOR UNIT INSTALLAION MAINTENANCE CAUTIONS TROUBLE SHOOTING 2 3 5 9 10 11 Please read this operation manual before using the air conditioner. Keep this operation manual for future reference. 0010535380 Parts and Functions Indoor Unit 1 8 1 2 5 3 Remote controller 10 6 7 8 9 4 11 FAN 2 13 18 ON/OFF 3 4 5 1 2 3 4 5 6 7 12 21 19 MODE SWING POWER/SOFT 15 23 20 14 TIMER CLOCK LIGHT SET SLEEP Inlet Inlet grille Outlet Vertical blade (adjust left and right air flow) 6 7 8 Display board Emergency Switch Air Purifying Filter (inside) 16 22 17 LOCK RESET Horizontal flap (adjust up and down air flow. Mode display Please be subject to the actual produce purchased the above picture is just from your reference Operation mode Remote controller AUTO COOL DRY HEAT FAN 2. LOCK button Used to lock buttons and LCD display. [. . . ] Please be subject to the actual product purchased, the above picture is just for your reference. 6 Indoor Unit Installation Fitting of the Mounting Plate and Positioning of the wall Hole When the mounting plate is first fixed 1. Carry out, based on the neighboring pillars or lintels, a proper leveling for the plate to be fixed against the wall, then temporarily fasten the plate with one steel nail. Make sure once more the proper level of the plate, by hanging a thread with a weight from the central top of the plate, then fasten securely the plate with the attachment steel nail. Find the wall hole location A using a measuring tape 1. Insert the drain hose into the dent of heat insulation materials of indoor unit. Insert the indoor/outdoor electric cable from backside of indoor unit, and pull it out on the front side, then connect them. Coat the flaring seal face with refrigerant oil and connect pipes. Cover the connection part with heat insulation materials closely, and make sure fixing with adhesive tape Indoor/outdoor electric cable Heat insulation material Lid for right piping Lid for under piping pipe Fix with adhesive tape Piping Pipe supporting plate Lid for left piping Drain hose B= Ø 60mm Indoor/outdoor electric cable and drain hose must be bound with efrigerant piping by protecting tape. [ Other direction piping ] A=145mm B= Ø 60mm Cut away, with a nipper, the lid for piping according to the piping direction and then bend the pipe according to theposition of wall hole. When bending, be careful not to crash pipes. Connect beforehand the indoor/outdoor electric cable, and then pull out the connected to the heat insulation of connecting part specially. 30mm Fixing the indoor unit body A=145mm 30mm When the mounting plate is fixed side bar and lintel Fix to side bar and lintel a mounting bar, Which is separately sold, and then fasten the plate to the fixed mounting bar. Refer to the previous article, " When the mounting plate is first fixed ", for the position of wall hole. Hang surely the unit body onto the upper notches of the mounting plate. Move the body from side to side to verify its secure fixing. In order to fix the body onto the mounting plate, hold up the body aslant from the underside and then put it down perpendicularly. mounting plate Making a Hole on the Wall and Fitting the Piping Hole Cover Make a hole of 60 mm in diameter, slightly descending to outside the wall. Install piping hole cover and seal it off with putty after installation Wall hole Unloading of indoor unit body When you unload the indoor unit, please use your hand to arise the body to leave agraffe, then lift the bottom of the body outward slightly and lift the unit aslant until it leaves the mounting plate. Ø60mm Indoor side Outdoor side Thickness of wall (Section of wall hole) G Piping hole pipe agraffe mounting plate Installation of the Indoor Unit Drawing of pipe Connecting the indoor/outdoor Electric Cable Removing the wiring cover Remove terminal cover at right bottom corner of indoor unit, then take off wiring cover by removing its screws. [ Rear piping ] Draw pipes and the drain hose, then fasten them with the adhesive tape [ Left Left-rear piping ] In case of left side piping, cut away, with a nipper, the lid for left piping. In case of left-rear piping, bend the pipes according to the piping direction to the mark of hole for left-rear piping which is marked on heat insulation materials. 7 When connecting the cable after installing the indoor unit 1. Insert from outside the room cable into left side of the wall hole, in which the pipe has already existed. Pull out the cable on the front side, and connect the cable making a loop. Correct Incorrect Lean Damage of flare Crack Partial Too outside On Drainage Please install the drain hose so as to be downward slope without fail. Please don't do the drainage as shown below. When connecting the cable before installing the indoor unit Insert the cable from the back side of the unit, then pull it out on the front side. Loosen the screws and insert the cable ends fully into terminal block, then tighten the screws. Pull the cable slightly to make sure the cables have been properly inserted and tightened. After the cable connection, never fail to fasten the connected cable with the wiring cover. Less than 5cm It becomes The end is imm- It waves. [. . . ] During unit operation or at stop, a swishing or gurgling noise may be heard. At first 2-3 minutes after unit start, this noise is more noticeable. (This noise is generated by refrigerant flowing in the system. ) During unit operation, a cracking noise may be heard. This noise is generated by the casing expanding or shrinking because of temperature changes. Should there be a big noise from air flow in unit operation, air filter may be too dirty. This is because the system circulates smells from the interior air such as the smell of furniture, paint, cigarettes. During COOL or DRY operation, indoor unit may blow out mist. [. . . ]