User manual HAIER BDW8NZ

[. . . ] - After removing the packing, check to make sure that the appliance is not damaged. If in doubt, contact a qualified professional. - The dishwasher must only be used by adults for the washing of household dishes and cooking utensils. - Fundamental rules to follow when using the appliance: * Never touch the dishwasher when barefoot or with wet hands or feet; * We discourage the use of extension cords and multiple sockets; E F Upper Rack Top Spray Arm Rack Height Adjustor Lower Rack Washing Filter J K L M V Salt Container Cap Bottom Spray Arm Detergent and Rinse Aid Dispenser Turbo Dry-fan Third Spray Arm Close-up View (control panel) M R G H Q 6h 4h 2h S S T B A WQP12-CBE 1 0 I 1 2 Technical characteristics P R D C Width Depth Height Capacity 60 cm 57 cm 82-84 cm 12 standard place settings 0. 03-0. 6MPa 220-240V~ 2150W A B C D Q ON-OFF Button ON-OFF Light Delay select button Delay indicator light "HALF LOAD" Button . 1. R T S P M "HALF LOAD" indicator light Mains water pressure Low rinse aid indicator light Power voltage Low salt indicator light Total absorber power Cycle select button Cycle indicator light . 2. Salt GB Detergent and Rinse Aid Detergent Detergent specifically intended for use with dishwashers must be used. [. . . ] If necessary, read the paragraph entitled, "Cancelling or modifying a cycle while underway. "The end of the cycle will be signalled by a double acoustic sound, and the indicator light "M" will begin to blink. Setting The Start Delay Time Open the door of the dishwasher partially. If the "C" button is pressed (see, Close-up View" Control Panel"). The start time for the wash cycle can be delayed for 2, 4 or 6 hours. Each time the button is pressed, the "D" light will come on indicating the length of the delay. After selecting the delay time, the wash cycle can be set, as explained in "Starting a wash cycle. . . " There will be a short acoustic signal, and at this point the delay period will begin to count down. During this period the delay indicator light (D) will blink. At the end of the delay time, the indicator will stop blinking and the cycle will start. fig. A fig. B Cancelling or modifying a cycle while underway. . . Premise: A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the NOTE: a) During the delay period, none of the settings can be modified. If necessary, they can be cancelled by pressing cycle selector "P" for about 5 seconds. b) If the power to the appliance goes off or the door is opened during the delay period, the clock will stop the countdown. It will start again when the power has come back on, or when the door has been closed. How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, coffee and tea cups and saucers, as well as plates, small bowls and shallow pans (as long as they are not too dirty). - Position the dishes and cookware so that they do not get moved by the spray of water. The upper rack can be adjusted for height by using the knobs located on the sides of the rack itself (see fig. C). 1 2 appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). 3 4 To change the cycle currently underway, open the door, press fig. C the "P" programming button and hold it in for about 5 seconds. Once the cycle has been cancelled, the dishwasher will emit a short acoustic sound and the relative indicator light will turn off. Wash Cycle Adjustment Buttons Warning Important wiring instructions for plug UK only WARNING: THIS APPLIANCE MUST BE EARTHED The cords in this mains lead are coloured in accordance with the following code: (see figure B) *Green/Yellow *Earth *Blue *Neutral *Brown * The core which is coloured GREEN/YELLOW must be connected to the terminal which is marked with the letter E or by the earth symbol or coloured GREEN/YELLOW. * The core which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The second pre-wash use cold . 30g How to keep Your Dishwasher in Shape After Every Wash After every wash, turn off the water supply to the appliance and leave the door slightly ajar so that moisture and odors are not trapped inside. Heavy Duty When You Go on Holiday When you go on holiday, it is recommended that you run a wash cycle with the dishwasher empty and then remove the plug from the socket, turn off the water supply and leave the door of the appliance slightly ajar. This will help the seals last longer and prevent odors from forming within the appliance. Normal dirty dishes, pots and pans. Extended wash at 55 Rinse with cold water. . 30g Remove the plug Before cleaning or performing maintenance, always remove the plug from the socket. Do not run risks. Normal Wash (IEC-EN50242) dard daily cycle. Moving the Appliance If the appliance must be moved, try to keep it in a vertical position. [. . . ] If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. fig. 1 Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm, Or let it run into the sink, making sure to avoid bending or crimping it. Use the special plastic support that comes with the appliance (see fig. 3). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. The Dishwasher Does Not Load Water Have you checked whether: - the water is turned on and the hose is connected properly; - the water supply to the house is on and has sufficient pressure; - the water supply hose is crimped or bent; - the filter for the water supply hose is clogged. vice centre and provide them with the following information: - the nature of the problem; - the model type number (Mod. . . ) And the serial number (S/N. . . ), which are indicated on the plate located on the side of the inner part of the door. The Dishes Are Not Clean Have you checked whether: - the water is turned on and the hose is connected properly; - the water supply to the house is on and has sufficient pressure; - the water supply hose is crimped or bent; - the filter for the water supply hose is clogged. Never call on unauthorised technicians and refuse to allow parts to be installed that are not original spare parts. Hot Water Connection MAX 100 MIN 40 The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60 . fig. 3 Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain. In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. [. . . ]