User manual HAIER BFD45W

[. . . ] Built-in installation Built-in installation(without worktop) remove the worktop Fresh-water connection ing transport, any water left inside may enclose parts and in accordance with the inseep into the control module and cause stallation instruction subsequcent error with programme Water pressure: function. The appliance must be drained in the folIf the water pressure is higher, install a lowing sequence: pressure reducing valve. - Set main switch to ON Connect the hose to a water tap using the - If the appiance is not kept upright dur- Installation instructions Individual installation Min. Diametere of sewage pipe:4cm Water temperature We recommend that you use cold water. [. . . ] This is not a fault but if it continues all the time, arrange for a service engineer to replace the seal. Knocking sound can be heard while washing is taking place - Aspray arm is knocking against the dishes inside the appliance. Plastic items are discoloured - Not enough detergent was added to dispenser. - Detergent has insufficient bleaching properties. Use a detergent containing a chemical bleaching agent. Caution Do not forget that repairs should only be carried out by a qualified inside dispenser specialist. Improper repairs can - Compartment was damp when it was filled up with detergent. lead to considerable equipment damage as well as danger to the user. Compartment must be dry before detergent is added. Remnants of detrgent stuck Rattling sound can be heard while washing is taking place - Crockey has not been stacked properly inside the appliance. Care and maintenance Interruping the programme - Set Start/Pause 9 to PAUSE. The programme is retained in the dishwasher memory. - If or the appliance has already heated up and then the appliance door ajar for several minutes and then close. Otherwise, the appliance door may fly open due to expansion. - In oder to continue with thestored programme, set the button 9 to START. Drying When a programme without drying process is selected, the dinner service is dried solely by afterheat - Press the 6 or 7 or 8 button, and set washing programme - Press the 6 or 7 or 8 button again, and set the programme to Drying. Care and maintenance Regular inspection and maintenance of your appliance helps to prevent problems from occurring. You should therefore carefully inspect the inside of your dishwasher from time to time. Overall condition of appliance - Check that no grease or scale has accumulated on the inside of the dishwasher. If you discover any deposits: - Clean the interior of the dishwasher thorough with a detergent solution. Spray arms Lime and remants of food in the washing water can block the nozzles in the spray arms 12 and 13 and the arm mountings. - Inspect the nozzles in the spray arms for blocked holes due to remnants of food. Programme the delay timer You can delay the start of a programme in increments of ONE hour for up to NINE hours. - Immediately press the Preset button 2 . - Press the Preset button as many times as necessary unit the numercial display shows the required delay. - To erase the time delay setting, keep pressing the Preset button until disappears in the numerical display. The timer function is cancelled if the dishwasher is switched off. You can change your programme selection as often as you like during the intervening period before the dishwasher starts up. Changing the programme Once selected, the programme can not be changed during operation. To be change the programme, switch off the main switch and repeat the programme. Filters The filters 14 prevent larger remnants of food or other objects from getting inside the pump. This residue can occasionally clog up the filters. - If necessary, pull the lower spray arm 13 upwards and lift it off. - Clean both spray arms under runing water. - Refit the spray arms. Ensure that the The filter system consists of a coarse/ lower arm has locked into place and the upper one is screwed tight. - Inspect the filters for obstructions every time the dishwasher has been used. After you have unscrewed the coarse/microfilter, you can lift out the fine filter. [. . . ] - Repairs or other work on the dishwasher should only be carried out by a qualified specialist. - The dishwasher must be disconnected from the electricity supply before any repairs or other work are started. Pull the mains plug out of the wall socket or switch off at the fuse box. Grasp the plug to remove it from the socket;do not tug on the cable. [. . . ]