User manual HAIER CW495

[. . . ] Integrated Dishwasher CW495 Users Operating Instructions Before operating this appliance, please read these instructions carefully Guarantee CDA appliance carry a five-year parts and one-year labour guarantee. CDA will repair or replace any defect or part attributable to faulty material or workmanship. Within the first year this will be free of both labour and parts charges. After the first year and within five years, the parts will be supplied free of charge provided that the repair is carried out by an agent authorised by CDA and the labour will be charged at the commercial rate applicable at the time of repair. [. . . ] The "B" indicator light will come on. At this point, the appliance is on and ready to be programmed. GB At the end of the wash cycle. . . The end of the cycle will be indicated by a double acoustical signal and the blinking of the "G" indicator light. And the number on the display "I" will turn "0". Open the door, turn off the appliance using the power botton and turn off the water supply to the unit. Wait a few minutes before removing the dishes so as to avoid handling them while still hot (when they are more susceptible to breakage) and to get better drying results. Setting and Starting a wash Cycle Choose the desired cycle by pressing the cycle selection button "H". Each time it is pressed, one of the cycle indicator lights "G" will come on in succession. At that time, the display "I" will show number of hours for the programme. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance). b) If the door is opened during the delay period, the indicator will blink and acoustic signal will sound, and the countdown will stop. It will begin again when the door is closed . To set a new wash cycle, follow the instructions contained in the paragraph entitled, "Setting and Starting a Wash Cycle". Wash Cycle Adjustment Buttons 1/2 Load Button If you forget to load some of the dishes. . . The wash cycle can be interrupted by opening the door carefully (in order to avoid being sprayed by hot water). When the door is closed again, the cycle will automatically restart at the point where it left off. This button (see "Close-up View-Control Panel", letter "D") makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load, This will allow you to save on water and electrical energy. It cannot be used with the heavy duty wash cycles. . 6. Wash Cycle Table GB Cycle Cycle Selection Information Description of Cycle Detergent Rinse Aid Very dirty dishes, pots and pans. (Not to be used with delicate items) Pre-wash with hot water. Extended wash at 70 Rinses with cold water. K 30g Intensive wash Normal dirty dishes, pots and pans. Standard daily cycle. pre-wash with cold water. Extended wash at 55 Rinse with cold water. . 30g Normal Wash Normal dirty dishes, pots and pans without dried on residue. Pre-wash with cold water. Extended wash at 50 Rinse with cold water. K 30g Light Wash (IEC-EN50242) ERF Economic, fast cycle to be used for items which are sensitive to higher. Wash at 60 Hot rinse. Drying. . Rinse with warm water. Glassware Run immediately after dishes are used. 15g Economic, fast cycle to be used to on not very dirty dishes right after they are used. No dry- Short wash at 40 Cold rinse. . 15g Rapid Wash ing cycle. Pre-wash of dishes, pots and pans while waiting for the load to Short cold wash to prevent food residue from drying on the dishes K Soak be completed after the subsequent meal. . 7. Energy Saving Tips -It is important to try and run the dishwasher when it is fully loaded in order to save on energy. [. . . ] If for any reason the box containing the electrical components happens to get damaged, remove the plug for the appliance from the socket immediately. In order to guarantee that the anti-flooding feature operates properly, the "A" box with water supply hose must be attached to the water supply tap as shown in Fig . 1. No other type of connection is acceptable. Caution: The dishwasher plug must be accessible even when the appliance is installed as a built-in unit so that maintenance can be done safety. . 10. Installation cont. . Stage 1 Supplied with the appliance is a plastic (self adhesive) anticondensation strip, this should be fixed to the underside of your worktop along the front edge. The adjustable feet of the appliance allow it to be raised up to 870mm, if the space between the floor and the underside of the work surface is greater than 870mm, fig 1a GB Stage 5 Align the top of the decor door with adjacent cabinets. [. . . ]