User manual HAIER DI454

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual HAIER DI454. We hope that this HAIER DI454 user guide will be useful to you.

Lastmanuals help download the user guide HAIER DI454.


Mode d'emploi HAIER DI454
Download
Manual abstract: user guide HAIER DI454

Detailed instructions for use are in the User's Guide.

[. . . ] Domestic dishwasher Di454 GB 0120505392 Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19 February 1973 (Low Voltage) and subse quent modifications; - 89/336/EEC of 3 May 1989 (Electromagnetic Compatibility) and subsequent modifications. - Carefully dispose of the packing material. - After removing the packing, check to make sure that the appliance is not damaged. [. . . ] Each time it is pressed, one of the cycle indicator lights "A" Setting The Start Delay Time Open the door of the dishwasher partially. If the "I" button is pressed (see, Close-up View" Control Panel"). The start time for the wash cycle can be delayed for 2, 4 or 6 hours. Each time the button is pressed, the "H" light will come on indicating the length of the delay. After selecting the delay time, the wash cycle can be set, as explained in "Starting a wash cycle. . . " There will be a short acoustic signal, and at this point the delay period will begin to count down. During this period the delay indicator light "H"will blink. At the end of the delay time, the indicator will stop blinking and the cycle will start. Load for 9 Standard Settings will come on in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance). Close the door and after a few seconds, a short acoustic signal will sound indicating that the wash cycle has begun and cannot be modified. If necessary, read the paragraph entitled, "Cancelling or modifying a cycle while underway. "The end of the cycle 1 2 will be signalled by a double acoustic sound, and the indicator light "A" will begin to blink. Cancelling or modifying a cycle while underway. . . A cycle that is underway can only be modified if it has only been running for a short time, otherwise, the detergent may have al- NOTE: a) During the delay period, none of the settings can be modified. If necessary, they can be cancelled by pressing cycle selector "E" for about 5 seconds. b) If the power to the appliance goes off or the door is opened during the delay period, the clock will stop the countdown. It will start again when the power has come back on, or when the door has been closed. How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, coffee and tea cups and saucers, as well as plates, small bowls and shallow pans (as long as they are not too dirty). Position the dishes and cookware so that they do not get moved by the spray of water. The upper rack can be adjusted for height. (See fig. B) fig. A fig. B ready been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). To change the cycle currently underway, open the door and press the ON-OFF button "C", follow the instructions contained in the paragraph entitled, "Setting and Starting a Wash Cycle. " Wash Cycle Adjustment Buttons If you forget to load some of the dishes. . . The wash cycle can be interrupted by opening the door carefully (in order to avoid being sprayed by hot water). When the door is closed again, the cycle will automatically restart at the point where it left off. 1/2 Load Button This button (see" Close-up View-Control Panel", letter "B") makes it possible to wash dishes using only the upper rack if there are not enough dishes for a full load, This will allow you to save on water and electrical energy. It cannot be used with the heavy duty wash cycles. . 5. GB GB . 6. Wash Cycle Table Energy Saving Tips -It is important to try and run the dishwasher when it is fully loaded in order to save on energy. [. . . ] If the appliance is level, it will help ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector, making sure that it is fastened tightly in place (see fig. 1). If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. The Dishwasher Does Not Load Water Have you checked whether: - the water is turned on and the hose is connected properly; - the water supply to the house is on and has sufficient pressure; - the water supply hose is crimped or bent; - the filter for the water supply hose is clogged. and/or the problem persists, contact the nearest authorised service centre and provide them with the following information: - the nature of the problem; - the model type number (Mod. . . ) And the serial number (S/N. . . ), which are indicated on the plate located on the side of the inner part of the door. fig. 2 Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60 . The Dishes Are Not Clean Have you checked whether: - the water is turned on and the hose is connected properly; - the water supply to the house is on and has sufficient pressure; - the water supply hose is crimped or bent; - the filter for the water supply hose is clogged. Never call on unauthorised technicians and refuse to allow parts to be installed that are not original spare parts. In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain. Electrical Connection After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is correct for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HAIER DI454

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual HAIER DI454 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag