User manual HAIER DI605DL

[. . . ] - If the supply cord is damaged, it must be replaced by the manufacture, its service agent of similarly qualified persons in order to avoid a hazard. This appliance complies with following EEC directives: - 73/23/EEC of 19/02/73(Low Voltage) and subsequent modifi cations; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. - Carefully dispose of the packing material. - After removing the packing, check to make sure that the appliance is not damaged. If in doubt, contact a qualified professional. [. . . ] The "A" indicator light will come on. At this point, the appliance is on and ready to be programmed. GB At the end of the wash cycle. . . The end of the cycle will be indicated by a double acoustical signal and the blinking of the "G" indicator light. And the number on the display "I" will turn "0". Open the door, turn off the appliance using the power botton and turn off the water supply to the unit. Wait a few minutes before removing the dishes so as to avoid handling them while still hot (when they are more susceptible to breakage) and to get better drying results. Setting and Starting a wash Cycle Choose the desired cycle by pressing the cycle selection button "H". Each time it is pressed, one of the cycle indicator lights "G" will come on in succession. At that time, the display "I" will show number of hours for the programme. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance). Close the door and after a few seconds, a short acoustic signal will sound indicating that the wash cycle has begun and cannot be modified. If necessary, read the paragraph entitled, "Cancelling or modifying a cycle while underway". The end of the cycle will be signalled by a double acoustic sound, and the indicator light "G" will begin to blink. Setting The Start Delay Time Open the door of the dishwasher partially. If the "D" button is pressed (see, Close-up View "Control Panel"). The start time of the wash cycle can be delayed for between 1 to 12 hours. Each time the button is pressed, the display "I" will show the number of hours for the delay period. After selecting the delay time, the wash cycle can be set, as explained in "Starting a wash cycle. . . " There will be a short acoustic signal, and at this point the delay period will begin to count down. During this period the delay indicator light "E" will blink. At the end of the delay time, the indicator will stop blinking and the cycle will start. Cancelling or modifying a cycle while underway. . . Premise: A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). NOTE: a) During the delay period, it is preferable not to change any of the settings. If it is necessary, all of the settings must be cancelled by pressing the power button"B" to indicate that all of the settings have been cancelled. At this point, all of the steps for "Setting the Wash Cycle with a delayed Start Time" and "setting and Starting a Wash Cycle" must be repeated, following the instructions contained in the corresponding sections. [. . . ] Use the special plastic support that comes with the appliance (see fig. 3). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60 . fig. 3 Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain. In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Electrical Connection After making sure that the voltage and frequency values for the current in the home correspond to those on the rating plate (located on the stainless steel inner door of the appliance) and that the electrical system is correct for the maximum voltage on the rating plate, insert the plug into an electrical socket which is earthed properly (the earthing of the appliance is a safety requirement mandated by law). If the electrical socket to which the appliance must be connected is not appropriate for the plug, replace the plug, rather than using adaptors or the like as they could cause overheating and burns. fig. 2 Anti-Flooding Protection The dishwasher is equipped with a system that stops the supply of water in the event of a problem with the water supply hose, or leaks within the unit, in order to prevent damage to your home. [. . . ]