User manual HAIER DW101NSS

[. . . ] - During installation the power cord must not be bent or flattened excessively. - If the appliance is not operating properly, disconnect the appliance from the power supply. This appliance complies with the following EEC directives: -73/23/EEC of 19/02/73(Low Voltage)and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. - Carefully remove and dispose of the packing material. - Check to make sure that the appliance is not damaged. If in doubt, contact the retailer it was purchased from. [. . . ] Long utensils should be placed in the horizontal position at the front of the upper rack. 3 4 1 2 Load for 12 Standard Settings fig. A fig. B How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, cups and saucers, as well as plates, small bowls and shallow pans. It is recommended that dishes placed in the upper rack are not too dirty . Position the dishes and cookware so that they do not get moved by the spray of water. The upper rack can be adjusted for height by using the knobs located on the sides of the rack itself (see fig. B). . 4. Turning on the Appliance Starting a wash cycle - Make sure that the plug for the appliance is inserted into the wall socket. - Make sure that the water supply is turned on to full pressure. - Load the dishwasher (see the section entitled, "Loading the Dishwasher" on page 4). - Pour in the detergent (see the section entitled, "Detergent and Rinse Aid" on page 3). - Turn the knob located on the right of the control panel in clockwise direction until the number or symbol for the cycle setting is aligned with the reference mark (see the section entitled, "Wash Cycle Table" on page 7). - Press the POWER button, and the POWER light will turn on. At this point, the wash cycle will begin. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. Cancelling or modifying a wash cycle setting A cycle that is underway can only be modified if it has been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent" on page 3). Press the POWER button, and the ON light will turn off. Rotate the knob in clockwise direction to the desired cycle setting (see the section entitled: Starting a wash cycle ?F. Then, turn the dishwasher back on using the POWER button. If you forget to load some of the dishes The wash cycle can be interrupted by pressing the POWER button. You can then load additional dishes and turn the appliance back on. The cycle will start where it left off. At the end of the wash cycle When the knob stops turning and is aligned with a STOP mark (see figure), the cycle has finished. Turn off the appliance using the POWER button, turn off the water supply and open the door of the dishwasher. Wash Cycle Adjustment Buttons Eco Button This button (see "close-up View - Control Panel" on page 1, letter "G" ) is used for normal dirty dishes, pots and pans. This button reduces the washing temperature from 60 =to 50 I=saving energy costs. It can be used before setting any of the wash cycles, except for the intensive cycles (if included in the wash cycle table ). [. . . ] Some models are fitted with an "Aquastop" water supply hose (see fig. 1) in which the small filter is already housed in the threaded end. If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60 . In this case, the wash cycle time will be shortened by about 15 minutes and the wash efficiency slightly reduced. [. . . ]