User manual HAIER DW12-AFM3S

[. . . ] - The appliance must be positioned so that the plug is accessible. - The carpet must not obstruct the opening when the appliance installing on the ground with carpet. - If the supply cord is damaged, it must be replaced by the manufacturer, its service agent of similarly qualified persons in order to avoid a hazard. This appliance complies with the following EEC directives: - 73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. - Carefully dispose of the packing material. - After removing the packing, check to make sure that the appliance is not damaged. [. . . ] - Deep pots should be slanted to allow the water to flow out. - The silverware basket can be doubled (see fig. A) so that only one section may be used when the silverware load is light. This also makes space for additional pots and pans on the lower rack. - Silverware should be placed in the silverware basket with the handles at the bottom; if the rack has side baskets, the spoons should be located individually into the appropriate slots. Especially long utensils should be placed in the horizontal position at the front of the upper rack. 3 4 1 2 Load for 12 Standard Settings fig. A fig. B How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, coffee and tea cups and saucers, as well as plates, small bowls and shallow pans (as long as they are not too dirty). Position the dishes and cookware so that they do not get moved by the spray of water. The upper rack can be adjusted for height. (See fig. B) Shelf Lean tall glasses and those with long stems against the shelf-not against other items to be washed(see fig. C). fig. C . 5. Starting the Appliance GB Starting a wash cycle - Make sure that the plug for the appliance is inserted into the wall socket. - Make sure that the water supply is turned on to full pressure. - Load the dishwasher (see the section entitled, "Loading the Dishwasher"). - Pour in the detergent (see the section entitled, "Salt, Detergent and Rinse Aid"). - Turn the knob located on the right of the control panel in the clockwise direction until the number or symbol for the cycle section entitled, "Wash Cycle Table"). - Press the ON-OFF button, and the ON-OFF light will turn on. At this point, the wash cycle will begin. At the end of the wash cycle When the knob stops turning and is aligned with a STOP mark (see figure), the cycle has finished. Turn off the appliance using the ON-OFF button, turn off the water supply and open the door of the dishwasher. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. Important: In general, it is not advisable to open the door while the machine is working. Care must be taken if the door is opened during the hot phase or immediately after a programm has finished as steam may escape. Cancelling or modifying a wash cycle setting Press the ON-OFF button and the ON Light will turn off. Rotate the knob in the clockwise direction to the desired cycle setting (see the section entitled, "Starting a wash cycle. . . "). Then, turn the dishwasher back on using the ON-OFF button. Wash Cycle adjustment Buttons =Button ====== This button (see "close-up View - Control Panel", letter "F") is used for normal dirty dishes, pots and pans. It is standard daily cycle. . 6. Wash Cycle Table GB Cycle Eco Button Cycle Selection Information Description of Cycle Pre-wash with hot water. [. . . ] In any case, the appliance should not be inclined more than 2 . If the appliance is level, it will help ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector and make sure that it is fastened tightly in place (see fig. If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. fig. 2 Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60 . [. . . ]