User manual HAIER DW12-BFEME

[. . . ] - After installation, the power plug must be accessible. To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: - call only the Service Centers authorized by the manufacturer. - always use original Spare Parts. This appliance complies with the following EEC directives: -73/23/EEC of 19/02/73(Low Voltage)and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. - Carefully dispose of the packing material. - After removing the packing, check to make sure that the appliance is not damaged. If in doubt, contact a qualified professional. [. . . ] A If drops of water remain on the dishes or spotting occurs, the dosage adjustor should be turned to a higher setting. If the dishes have white streaks, turn the dosage adjustor to a lower setting. B C Extended wash F C Notice:To facilitate closing the cover, remove any excess detergent on the edges of the dispenser. GB . 4. Loading the Dishwasher Before placing the dishes in the dishwasher, remove the large food particle to prevent the filter from becoming clogged, which results in reduced performance. If the pots and pans have baked-on food that is extremely hard to remove, we recommend that they be allowed to soak before they are washed. This will eliminate the need for extra wash cycles. Pull out the rack to facilitate loading the dishwasher. Lower Rack Upper Rack How to Use the Lower Rack We recommend that you place the most difficult to clean items on the lower rack:pots , lids, serving dishes and bowls, as shown in the figure on the right. It is preferable to place serving dishes and lids on the sides of the racks in order to avoid blocking the rotation of the top spray arm. - Pots, serving bowls, etc. must always be placed top down. - Deep pots should be slanted to allow the water to flow out. - The silverware basket can be doubled(see Fig. A) so that only one section may be used when the silverware load is light. This also makes space for additional pots and pans, and it can also be placed in the upper rack. - Silverware should be placed in the silverware basket with the handles at the bottom;if the rack has side baskets, the spoons should be located individually into the appropriate slots. Especially long utensils should be placed in the horizontal position at the front of the upper rack. Load for 12 Standard Settings 1 2 3 4 Fig. A Fig. B How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, coffee and tea cups and saucers, as well as plates, small bowls and shallow pans(as long as they are not too dirty). - Position the dishes and cookware so that they do not get moved by the spray of water. The upper rack can be adjusted for height by using the knobs located on the sides of the rack itself (see Fig. B). . 5. GB Turning on the Appliance Starting a wash cycle After having completed all of the installation steps in the preceding paragraphs, turn on the water all the way and press the ON-OFF button (A) located on the control pannel. The "B" indicator light will come on. At this point, the appliance is on but you must wait a few seconds before programming the setting for the cycle. Setting the Wash Cycle with a Delayed Start Time Premise: After selecting the wash cycle as indicated in the paragraph entitled , "Setting and Starting a Wash Cycle. . . "the delay time can be set. By pressing the "E" button (see close-up view-'Control panel") the start of wash cycle can be delayed for between 1 to 12 hours. Each time the button is pressed, the display (F) will show the number of hours for the delay period. Choose the amount of time desired. When the appliance is started with "I" button, a short acoustic signal will sound and the delay time on the display will blink , indicating that the countdown has begun. Setting and Starting a wash Cycle Select the desired cycle by pressing the selector button (G). Each time the button is pressed, one of the"H" cycle indicator lights will come on in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance). Press the Start/Pause button(I), and after a few seconds a short acoustic sound will indicate that the wash cycle has begun and can no longer be changed. If necessary , read the paragraph entitled " Cancelling or modifying a cycle while underway. . . " After the time has elapsed, the cycle will start. Cancelling or modifying a cycle while underway Premise : A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance mayhave already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). [. . . ] If, despite all these checks, the dishwasher still does not function and/or the problem persists, contact the nearest authorised service centre and provide them with the following information: - the nature of the problem; - the model type number (Mod. . . )and the serial number (S/N. . . ), which are indicated on the plate located on the side of the inner part of the door. The Dishwasher Does Not Load Water Have you checked whether: - the water is turned on and the hose is connected properly; - the water supply to the house on and has sufficient pressure; - the water supply hose is crimped or bent; - the filter for the water supply hose is clogged. Never call on unauthorised technicians and allow the parts which are not original spare parts to be installed . . 9. GB Installation Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned on the right or the left to facilitate proper installation. Levelling the Appliance Once the appliance is positioned, adjust the feet (screw them in or out) to level the dishwasher. In any case, the appliance should not be inclined more than 2 . If the appliance is level, it will help ensure proper performance. Fig. 1 Cold Water Connection Connect the cold water supply hose to a threaded 3/4(gas) connector and make sure that it is fastened tightly in place (see Fig 1). If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. Drain Hose Connection Insert the drain hose into a drain pipe with a minimum diameter of 4cm, or let it run into the sink, making sure to avoid bending or crimping it. Use the speical plastic support that comes with the appliance (see Fig. 2). The free end of the hose must be at a height between 40 and 100 cm and must not be immersed in water. Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60 . [. . . ]