User manual HAIER DW12-HFE2

[. . . ] Installation DW12-HFE2 Diagram The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product. GB Code:0120504583 Safety Is a Good Habit to Develop NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential to safe and proper installation, use and maintenance of the appliance. [. . . ] How to use the upper rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, cups and saucers, plates, small bowls and shallow pans (as long as they are not too dirty). - Position the dishes and cookware so that they do not get moved by the spray of water. Adjust the upper basket to the higher level and you have more space to accommodate those taller pans and trays in the bottom basket. Shelf Lean tall glasses and those with long stems against the shelf-not against other items to be washed. Place glasses, cups and small bowls on the additional cup rack. The additional cup rack can be swivelled in or out as required(see fig. C). Knife rack The knife rack clips onto the side of the top basket, giving you the freedom to wash your large sharp knives separately and out of harm's way (see fig. D). Lower Rack Upper Rack Starting a wash cycle After having completed all of the installation steps in the preceding paragraphs, turn on the water all the way and press the ONOFF button (B) located on the control pannel. The "A" indicator light will come on. At this point, the appliance is on but you must wait a few seconds before programming the cycle setting. Setting and Starting a wash Cycle Select the desired cycle by pressing the selector button (I). Each Setting the Wash Cycle with a Delayed Start Time By pressing the "D" button (see close-up view-'Control panel") the start of wash cycle can be delayed for between 1 to 12 hours. Each time the button is pressed, the display (C) will show the number of hours for the delay period. After selecting the wash cycle, a short acoustic signal will sound and after a few seconds, the delay time on the display will blink, This indicates that the countdown has begun. After the time has lapsed, the cycle will start. Load for 12 Standard Settings time the button is pressed, one of the "J" cycle indicator lights will come on in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual. After a few seconds, the wash cycle has begun and can no longer be changed. If necessary, read the paragraph entitled "Cancelling or modifying a cycle" . NOTE: During the delay period, it is preferable not to change any of the settings, If this is necessary, all of the settings must be cancelled by pressing the ON/OFF button (B). At this point, all of the steps for "setting the wash cycle with a Delayed Start Time" and "Setting and Starting a wash cycle" must be repeated, following the instructions contained in the corresponding sections. If the door is opened to the unit during the delay period, the countdown will stop. It wil begin again when the door is closed. All of the wash cycle set to reverse time function, we may in focus stat circulate time. Cancelling or modifying a cycle Load for 12 Standard Settings (for IEC-EN 50242 tests) A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance mayhave already drained the wash water. [. . . ] If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), feature operates properly, the box "A" with the water supply hose must be attached to the water supply tap as shown in Fig. 1. No other type of connection is acceptable. [. . . ]