User manual HAIER DW201W-TU

[. . . ] Check that the detergent receptacle is empty after completion of the wash cycle. To maintain the EFFICIENCY and SAFETY of this appliance, we recommend: - call only service centres authorised by the manufacturer. - always use original Spare Parts. This appliance complies with the following EEC directives: -73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications; - 89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications. - Carefully dispose of the packing material. - After removing the packing, check to make sure that the appliance is not damaged. [. . . ] Especially long utensils should be placed in the horizontal position at the front of the upper rack. How to use the upper rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, cups and saucers, plates, small bowls and shallow pans (as long as they are not too dirty). - Position the dishes and cookware so that they do not get moved by the spray of water. Shelf Lean tall glasses and those with long stems against the shelfnot against other items to be washed (see fig. C). Long items, serving cutlery, salad, servers or knives should be placed on the shelf so that they do not obstruct the rotation of the spray arms. The shelf can be folded back when not required for use. fig. B fig. C A1 A2 A3 fig. A Lower Rack Upper Rack Load for 12 Standard Settings . 4. Turning on the Appliance Starting a wash cycle After having completed all of the installation steps in the preceding paragraphs, turn on the water all the way and press the ON-OFF button (A) located on the control panel. The "B" indicator light will come on. At this point, the appliance is on but you must wait a few seconds before programming the setting for the cycle. Setting the Wash Cycle with a Delayed Start Time Premise: After selecting the wash cycle as indicated in the paragraph entitled, "Setting and Starting a Wash Cycle. . . " the delay time can be set. By pressing the "E" button (see close-up view-'Control panel") the start of wash cycle can be delayed for between 1 to 9 hours. Each time the button is pressed, the display (F) will show the number of hours for the delay period. When the appliance is started with "I" button, a short acoustic signal will sound and the delay time on the display will blink, indicating that the countdown has begun. After the time has lapsed, the cycle will start. Setting and Starting a wash Cycle Select the desired cycle by pressing the selector button (G). Each time the button is pressed, one of the "H" cycle indicator lights will come on in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance). Press the Start/Pause button (I), and after a few seconds a short acoustic sound will indicate that the wash cycle has begun and can no longer be changed. If necessary, read the paragraph entitled"Cancelling or modifying a cycle while underway. . . " NOTE: a) During the delay period, it is preferable not to change any of the settings. If it is necessary, all of the settings must be cancelled by pressing the ON-OFF button (A) to indicate that all of the settings have been cancelled. At this point, all of the steps for "Setting the Wash Cycle with a delayed Start Time" and "setting and Starting a Wash Cycle" must be repeated, following the instructions contained in the corresponding sections. b) If the door is opened during the delay period, the indicator will blink and acoustic signal will sound, and the countdown will stop. It will begin again when the door is closed . Cancelling or modifying a cycle while underway Premise : A cycle that is underway can only be modified if it has only been running for a short time. Otherwise, the detergent may have already been used, and the appliance mayhave already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). [. . . ] If the appliance is level, it will help ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector and make sure that it is fastened tightly in place (see Fig 1). If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. If this precaution is not taken, there is a risk that the water inlet can get blocked and damage the appliance. MAX100 MIN40 Fig. 2 Attention: The special plastic hose support must be solidly fastened to the wall to prevent the drain hose from moving and allowing water to spill outside the drain. Electrical Connection Fig. 1 Hot Water Connection The water supply to the appliance can also be connected to the house's hot water line (centralised system, heating system), as long as it does not exceed a temperature of 60ç`. [. . . ]