User manual HAIER DW45BI

[. . . ] 45cm Fully Integrated Dishwasher DW45BI 0120505377 Dear customer, Thank you for purchasing this high quality product, designed and manufactured to satisfy all up-to-date requirements and guarantee prolonged lifetime in keeping with all your expectations. Safety Is a Good Habit to Get Into NOTICE Carefully read the instructions contained in this manual, as they provide important information which is essential for safe and proper installation, use and maintenance of the appliance. This appliance complies with the following EEC directives: - 73/23/EEC of 19 February 1973 (Low Voltage) and subse quent modifications; - 89/336/EEC of 3 May 1989 (Electromagnetic Compatibility) and subsequent modifications. - Carefully dispose of the packing material. - After removing the packing, check to make sure that the appliance is not damaged. [. . . ] Wait a few minutes before removing the dishes so as to avoid handling them while still hot (when they are more susceptible to breakage) and to get better drying results. Very dirty dishes, Pre-wash with hot water. Extended wash at 65 Rinse with cold water. Extended wash at 55 Rinse with cold water. Extended wash at 50 Rinse with hot waterK Drying. (Not to be used with delicate items) Cycle Cycle Selection Information Description of Cycle Detergent Rinse Aid Setting and Starting a wash Cycle Choose the desired cycle by pressing the cycle selection button "E". Each time it is pressed, one of the cycle indicator lights "A" will come on in succession. Choose the wash cycle you feel is most appropriate for the type of dishes that need washing (consult the wash cycle table contained in this manual, especially when first using the appliance). Close the door and after a few seconds, a short acoustic signal will sound indicating that the wash cycle has begun and cannot be modified. If necessary, read the paragraph entitled, "Cancelling or modifying a cycle while underway. "The end of the cycle will be signalled by a double acoustic sound, and the indicator light "A" will begin to blink. Setting The Start Delay Time Open the door of the dishwasher partially. If the "I" button is pressed (see, Close-up View" Control Panel"). The start time for the wash cycle can be delayed for 2, 4 or 6 hours. Each time the button is pressed, the "H" light will come on indicating the length of the delay. After selecting the delay time, the wash cycle can be set, as explained in "Starting a wash cycle. . . " There will be a short acoustic signal, and at this point the delay period will begin to count down. During this period the delay indicator light "H"will blink. At the end of the delay time, the indicator will stop blinking and the cycle will start. 30g Heavy Duty 30g Normal Wash Normal dirty dishes, pots and pans without dried on residue. 30g Cancelling or modifying a cycle while underway. . . A cycle that is underway can only be modified if it has only been running for a short time, otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent"). Before calling for assistance, Iet us see what can be done first: have you forgotten to press one of the buttons or to perform an essential operation? GB -Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment. -There is no advantage in rinsing dishes, cookware and utensils before placing them in the dishwasher. Error Messages The dishwasher is equipped with a safety system that is able to detect operating problems and malfunctions. These malfunctions are signalled by the rapid blinking of one of the "A" program LEDs. Only in the case where the indicator light for the soak cycle (see table for cycles) blinks rapidly should you cancel the cycle as The Dishwasher Does Not Start Have you checked whether: - the plug is pushed into the socket correctly; - the power is on in the house; - the door is closed properly; - the ON-OFF switch is on "ON"; - the water supply is turned on. described in the section entitled, "Changing a Cycle while Underway". [. . . ] In any case, the appliance should not be inclined more than 2°. If the appliance is level, it will help ensure proper performance. fig 1a using the fixing screws provided as shown in the diagram. Cover the screw heads using the plastic caps provided. the work surface is greater than 870mm, then the appliance should be positioned on suitable wooden spacers which should always be fixed to the floor. Always use a spirit level to make sure that the appliance is level left to right and front to back. (If the appliance is installed on a carpet, ensure there is clearance beneath the appliance). [. . . ]