User manual HAIER FDF6SE1

[. . . ] - Do not lean or sit on the door when it is open as this could overturn the dishwasher. - Do not touch the heating element during or after a wash cycle. - If the appliance malfunctions turn off water supply to the appliance and disconnect the plug from the wall socket. Refer to GB Close-up View (Interior) GB the section entitled, "Troubleshooting". [. . . ] This also makes space for additional pots and pans, and it can also be placed in the upper rack. - Silverware should be placed in the silverware basket with the handles at the bottom. If the rack has side baskets, the spoons should be loaded individually into the appropriate slots. Long utensils should be placed in the horizontal position at the front of the upper rack. B Important Proper dosage of the rinse aid improves drying. If drops of water remain on the dishes or spotting occurs, the dosage adjuster should be turned to a higher setting. If the dishes have white streaks, turn the dosage adjuster to a lower setting. Load for 12 Standard Settings CA C NOTE: To facilitate closing the cover, remove any excess detergent on the edges of the dispenser. How to Use the Upper Rack The upper rack is designed to hold more delicate and lighter dishware, such as glasses, cups and saucers, as well as plates, small bowls and shallow pans. It is recommended that dishes placed in the upper rack are not too dirty . Position the dishes and cookware so that they do not get moved by the spray of water. 3 4 1 2 F The upper rack can be adjusted for height by using the knobs located on the sides of the rack itself (see fig. B). fig. A fig. B . 3. . 4. Turning on the Appliance GB Energy Saving Tips GB Starting a wash cycle - Make sure that the plug for the appliance is inserted into the wall socket. - Make sure that the water supply is turned on to full pressure. - Load the dishwasher (see the section entitled, "Loading the Dishwasher" on page 4). - Pour in the detergent (see the section entitled, "Detergent and Rinse Aid" on page 3). - Turn the knob located on the right of the control panel in clockwise direction until the number or symbol for the cycle setting is aligned with the reference mark (see the section entitled, "Wash Cycle Table" on page 7). - Press the POWER button, and the POWER light will turn on. At this point, the wash cycle will begin. Wait a few minutes before unloading the dishwasher to avoid handling the dishes and utensils while they are still hot and more susceptible to breakage. They will also dry better. - It is important to try and run the dishwasher when it is fully loaded to save on energy. In order to prevent odors from forming and food from caking onto the dishes, you can run the Pre-Rinse cycle. - Choose the right wash cycle: the choice of cycle depends on the type of dishware, cookware and utensils being washed and how dirty they are. - Use the right amount of detergent: if you use too much detergent, the result will not be cleaner dishes, but, rather, a greater negative impact on the environment. Cancelling or modifying a wash cycle setting A cycle that is underway can only be modified if it has been running for a short time. Otherwise, the detergent may have already been used, and the appliance may have already drained the wash water. If this is the case, the detergent dispenser must be refilled (see the paragraph entitled, "Loading the Detergent" on page 3). Press the POWER button, and the ON light will turn off. [. . . ] The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the left to ensure correct installation. GB Installation GB The connection must be made to the hot water line following the same procedures as those for the connection to the cold water line. Anti-Flooding Protection The dishwasher is equipped with a system that stops the supply of water in the event of a problem with the water supply hose, or leaks within the unit, in order to prevent damage to your home. Levelling the Appliance Once the appliance is positioned, adjust the feet (screwing them in or out) to adjust the dishwasher, making it level. The appliance should not be inclined more than 2 . If the appliance is level, it will help ensure proper performance. Cold Water Connection Connect the cold water supply hose to a threaded 3/4 (gas) connector and make sure that it is fastened tightly in place (see fig. 1). If the water pipes are new or have not been used for an extended period of time, let the water run to make sure that the water is clear and free of impurities. [. . . ]