User manual HAIER H2SM-14H03R2

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL H2SM-(9+12)H03/R2 Please read this operation manual before using the air conditioner. No. 0010557183 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner Consult your local authorities for the name and address of the waste materials collecting in order to avoid the risk of child entrapment. centers and waste paper disposal services nearest to your house. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. [. . . ] Then, it will become normal. 6 Operation Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7 m without any obstacle as well. Don't throw the controller, prevent it from being damaged. When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter. Loading of the battery Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder) Remove the battery cover: Slightly press " " and push down the cover. Load the battery: Be sure that the loading is in line with the" + "/"-" pole request as illustrated. Put on the cover again Confirmation indicator: In disorderation, reload the batteries or load the new batteries after 6 mins. Note: Use two new same-typed batteries when loading. If the remote controller can't run normally or doesn't work at all, use a sharp pointed item to press the reset key. Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out just need to press reset key. Power failure resume(please set and apply as necessary) If sudden power failure occurs, the unit will resume original operation when power is supplied again. Note: When sudden power failure happens during unit operation in power failure resume mode, if the air conditioner is not desired for use in a long period, please shut off the power supply in case that the unit automatically resume operation when power is re-supplied, or press ON/OFF to turn off the unit when power resumes. 7 Operation Auto run, Fan operation (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. Enjoy yourself by just a gentle press. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN Unit will run in selected mode. Stop display at " " AUTO or " "FAN. (3) FAN Press FAN button. For each press, fan speed changes as follows: LO MED HI AUTO (4) Unit stop Unit will run at selected fan speed. Vertical flap closed automatically. Hints Remote controller can memorize settings in each operation mode. Referring to the Fig. COOL About 10 o HEAT About 60o Left and right air flow adjustment Press SWING button, vertical flap will move within (manual) Up and down (Use remote controller) the range shown in the Fig. Press SWING button stop it at a fixed position. Move the horizontal blade by a knob on air conditioner to adjust left and right direction referring to Fig. About 10o COOL About 45o HEAT About 60o Cautions: It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur. Cautions: When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right. (6) Unit stop Press ON/OFF button. Vertical flap closes automatically. Cautions: Unit won't restart until 3 minutes have elapsed, due to system protection. HEAT mode is not available on cooling only unit. Hints As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. As warm air flows upward in HEAT mode, adjusting air flow downward will be much more helpful for a better air circulation. Be careful not to catch a cold when cold air blows downward. It is harmful to your health in summer to go frequently in and out of places where temp. difference of 3-5 C will remove your fatigue. More than this, unit's load can be reduced and power consumption cut down as well. [. . . ] After washing, dry the filter completely in the shade. 2. Remove air filter Push up the filter's center tab slightly until it is caesura of the stopper. Remove it by pulling down. 5. Close the inlet grille. 4. Attach the filter Attach filter behind the stopper so that the "Front" indication is facing to the front. Make sure that it is completely behind the stopper, otherwise problems might occur. 16 Maintenance Replacement of Purifying Filter 1 Open the Inlet Grille Open the inlet grille by pushing each end of the inlet grille upward. 2 Detach the standard air Filter Slide the knob slightly upward to release the filter, then withdraw it. 3 Detach the Air Purifying Filter Replace old Air Purifying Filter with new one into the frame. Air Filter 4 Attach the Air Purifying Filter Attaching each of the Air Purifying Filters to the indoor unit as white side face to front. For the units of 22, the purifying filter is put into the standard filter. Air Purifying Filter 5 Attach the standard air Filter (make sure to be attached) Operating without standard air filter may cause trouble with the machine. 6 Close the inlet Grille Close the Grille surely. [. . . ]