User manual HAIER H2SM-18HA03

[. . . ] Per maggiori informazioni contattare l'installatore o le autorità locali. Le batterie devono essere tolte dal telecomando e smaltite separatamente conformemente alla legislazione locale e nazionale vigente in materia. EN EUROPEAN REGULATIONS CONFORMITY FOR THE MODELS: HSU-07HEA03/R2 HSU-09HEA03/R2 HSU-12HEA03/R2 HSU-18HEA03/R2 HSU-22HEA03/R2 CE All the products are in conformity with the following European provision: - Low Voltage Directive 73/23/EEC - Low Voltage Directive 2006/95/EC - Electromagnetic CompatibilitY 89/336/EEC - Electromagnetic CompatibilitY 2004/108/EC ROHS The products are fulfilled with the requirements in the directive 2002/95/EEC of the European parliament and of the council on the Restriction of the use of Certain Hazardous Substances in Electrical and Electronic Equipment (EU RoHS Directive). WEEE In accordance with the directive 2002/96/CE of the European parliament, herewith we inform the consumer about the disposal requirements of the electrical and electronic products. DISPOSAL REQUIREMENTS: Your air conditioning product is marked with this symbol. This means that electrical and electronic products shall not be mixed with unsorted household waste. [. . . ] TIMER Used to confirm timer and clock settings. Used to select TIMER ON, TIMER OFF, TIMER ON-OFF Used to set correct time 22. Ambient temp. display AUTO LO MED HI Used to reset the controller back to normal condition. When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed and this room temperature is only for reference. Clock set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working. NOTE: Cooling only unit do not have displays and functions related with heating Hints: After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal. 7 Operation Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well. Don't throw the controller, prevent it from being damaged. When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter. Loading of the battery Load the batteries as illustrated. Previous operation status appears on display. (Not Timer setting) (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN A U T O ON/OFF TEMP 5 1 MODE 3 3 SET Unit will run in operation mode displayed on LCD. Stop display at your desired mode. 2 FAN TIMER (3) Select temp. o Every time the button is pressed, temp. setting increases 1 C o Every time the button is pressed, temp. setting decreases 1 C Unit will start running to reach the temp. setting on LCD. 4 SWING CLOCK SLEEP HEALTH (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: LOCK RESET AUTO LO MED HI COOL operation starts when room temp. setting. Ultra-low air flow Unit runs at the speed displayed on LCD. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. Temp. [. . . ] o Heating when the room temperature at the start of operation is below 23 C o Test operation switch is the same as emergency switch. Use this switch in the test operation when the room o temperature is below 16 C, do not use it in the normal operation. Continue to press the test operation switch for more than 5 seconds. After you hear the "Pi" sound twice, release your finger from the switch: the cooling operation starts with the air flow speed "Hi". [. . . ]