User manual HAIER H2SM-H03-R2

[. . . ] Air Conditioner Edition:2005/11/18 OPERRATION Air Conditioner 2006/1/10 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner Consult your local authorities for the name and address of the waste materials collecting in order to avoid the risk of child entrapment. centers and waste paper disposal services nearest to your house. It must be noticed that air conditioner system contains refrigerants, which require specialiSafety Instructions and Warnings zed waste disposal. [. . . ] SET Used to confirm timer and clock settings 26. HOUR Used to set clock and timer settings 27. LOCK Used to lock buttons and LCD display. NOTE:(1)The following functions and related displays are not available: AUXILIARY HEAT display, POWER/SOFT display, HEALTH display. (2)If the Air conditioner don't have the function of the code , press code B can cause it not available. (3)Cooling only unit do not have functions and displays related with heating. Clock set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working. Hints After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal. Air Conditioner 2006/1/10 Operation Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7 m without any obstacle as well. Don't throw the controller, prevent it from being damaged. When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter. Loading of the battery Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder) Remove the battery cover: Slightly press " " and push down the cover. Load the battery: Be sure that the loading is in line with the" + "/"-" pole request as illustrated. Put on the cover again Confirmation indicator: In disorderation, reload the batteries or load the new batteries after 6 mins. Note: Use two new same-typed batteries when loading. If the remote controller can't run normally or doesn't work at all, use a sharp pointed item to press the reset key. Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out just need to press reset key. Power failure resume(please set and apply as necessary) If sudden power failure occurs, the unit will resume original operation when power is supplied again. Note: When sudden power failure happens during unit operation in power failure resume mode, if the air conditioner is not desired for use in a long period, please shut off the power supply in case that the unit automatically resume operation when power is re-supplied, or press ON/OFF to turn off the unit when power resumes. Air Conditioner 2006/1/10 Operation Auto run, Fan operation (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. Enjoy yourself by just a gentle press. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN Unit will run in selected mode. Stop display at " " AUTO or " "FAN. (3) FAN Press FAN button. For each press, fan speed changes as follows: LO MED HI AUTO (4) Unit stop Unit will run at selected fan speed. When starting it next time, just press ON/OFF button and unit will run in previous status. Air Conditioner 2006/1/10 Operation (5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. Referring to the Fig. COOL About 10 o HEAT About 60o Left and right air flow adjustment Press SWING button, vertical flap will move within (manual) Up and down (Use remote controller) the range shown in the Fig. Press SWING button stop it at a fixed position. Move the horizontal blade by a knob on air conditioner to adjust left and right direction referring to Fig. About 10o COOL About 45o HEAT About 60o Cautions: It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur. Cautions: When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right. (6) Unit stop Press ON/OFF button. [. . . ] After you hear the "Pi" sound twice, release your finger from the switch, the cooling operation starts with the air flow speed setting "Hi". Pi Pi Removal of the restriction of emergency or test operation: Press once more the emergency operation switch, or manipulate through the remote controller, a "Pi" sound causes the restriction of emergency or test operation to be removed. When the remote controller is manipulated for the removal, then the selected operation by the remote controller. Air Conditioner 2006/1/10 Operation Comfortable SLEEP Before going to bed at night, you can simply press the SLEEP button and unit will bring you a sound sleep in selected mode. In COOL mode One hour after SLEEP mode starts, temp. Unit will run for 6 hours then stops automatically. won't be too Iow for your sleep. (As shown in Fig. l) o o In HEAT mode One hour after SLEEP mode starts, temp. [. . . ]