User manual HAIER HS-08CD12

[. . . ] For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN 3 3 Then Select COOL operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1oC, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting increase 1oC, if kept depressed, it will decrease rapidly Select a desired temperature. 2 4 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: AUTO HI LOW 1 5 When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. Cautions To protect unit system, don`t restart until 3 minutes have elapsed If the unit has been running under large humidity for a long time, dew might occur at outlet grating 6 Air Conditioner Edition:2006/02/07 Auto mode 1. [. . . ] After unit starts, select your desired operation mode Operation mode will be displayed on LCD. Timer mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: Remote controller: SLEEP TIMER OFF TIMER ON BLANK 2 3 Then select your desired TIMER mode (TIMER ON or TIMER OFF). 3 3. Time setting Press HOUR button. Every time the button is pressed, time setting increases 1 min, if kept depressed, it will increase rapidly. Every time the button is pressed, time setting decreases 1 min, if kept depressed, it will decrease rapidly. Time setting is available within 1-12Hrs. Time displayed shows how many hours later unit will start of stop 1 4 4. Cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. Cautions TIMER function is not available in SLEEP mode. 8 Air Conditioner Edition:2006/02/07 Dry Mode Remote Controller 1. Unit start Press ON/OFF on the remote controller, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN 3 3 Then Select DRY operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting increase 1 C, if kept depressed, it will decrease rapidly Select a desired temperature. 1 2 4 5 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: AUTO HI LOW Air conditioner is running under displayed fan speed. 5. Unit stop Press ON/OFF button, the unit stops. Cautions Unit will run intermittently in Dry mode with fan speed at "LOW", regardless of its setting. Air blown out will be very cold at relatively low room temp. compressor runs intermittently , fan motor will be in low speed. 9 Air Conditioner Edition:2006/02/07 Fan operation Remote Controller 1. Unit start Press ON/OFF on the remote controller, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN Then Select FAN operation 2 3. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: HI LOW 3 Select desired fan speed. Change air flow if necessary 1 4 4. Unit stop Press ON/OFF button, the unit stops. Hints In FAN operation mode, the unit will not operate in COOL mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP operation is not available. 10 Air Conditioner Edition:2006/02/07 Health operation 1. Unit start Press ON/OFF on the remote controller, unit starts. Remote Controller 2. Select operation mode Press MODE button. [. . . ] setting so that room temperature won't be too Iow for your sleep. In AUTO mode The unit operates in corresponding sleep mode adapted to the automatically selected operation mode. 4. Set the wind speed change when sleeping If the wind speed is high or middle before setting for the sleep, set for lowing the wind speed after sleeping. [. . . ]