User manual HAIER HSU-07C03

[. . . ] PS AREPO HSU-088M06 HSU-098M06 HSU-108M06 HSU-128M06 HSU-188M06 l o P N noC a a p a r C P O M T 1 2-4 5-13 14-15 16 Cautions The machine is adaptive in following situation I. Applicable ambient temperature range: Indoor Cooling Outdoor Indoor Heating Outdoor Maximum: Minimum: Maximum: Minimum: Maximum: Minimum: Maximum: Minimum: D. B / W. B D. B / W. B D. B D. B D. B D. B D. B / W. B D. B / W. B 32 C/23 C o o 18 C/14 C o o 43 C/26 C o 18 C o 27 C o 15 C o o 24 C/18 C o o -7 C/-8 C o o 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F 3. [. . . ] For each press, fan speed changes as follows: SLEEP HEALTH LOCK RESET AUTO LO MED HI (4) Unit stop Unit will run at selected fan speed. Vertical flap closed automatically. Hints Remote controller can memorize settings in each operation mode. To run it next time just select the operation mode and it will start with the previous setting. No reelecting is needed. (TIMER ON/OFF needs reelecting) Cautions: Note: On cooling only unit, heating mode is not available, The above information is the After replacing batteries, press ON/OFF, and display explanation of the displayed becomes as follows: information therefore varies Operation mode: AUTO, Temp. No with those displayed in actual Timer mode: No, Fan speed :AUTO operation. Operation COOL, HEAT and DRY operation Recommendations: (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. Timer setting) (Not Power indicator on indoor unit lights up. Use COOL in summer. Use HEAT in winter Use DRY in spring, autumn and in damp climate. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: ON/OFF TEMP AUTO COOL DRY FAN MODE SET Unit will run in operation mode displayed on LCD. Stop display at your desired mode. (3) Select temp. o Every time the button is pressed, temp. setting increases 1 C o Every time the button is pressed, temp. setting decreases 1 C Unit will start running to reach the temp. setting on LCD. FAN TIMER SWING CLOCK SLEEP HEALTH (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: LOCK RESET AUTO LO MED HI COoeaintrshnom OLprtosatwero tm. ihraepetn. epsgehnm. tig i tt s h Urlio laorw t-al w f Unit runs at the speed displayed on LCD. Tm. tig2 epetn+C so Tm. tig epetn s In DRY mode, when room temperature becomes o lower than temp. setting+2 C, unit will run intermittently at LOW speed regardless of FAN setting. Oecigm. tignt nahnepetn, i r ts u w l r ni m l D Ym d . il u n id R oe Hints On cooling only unit, heating mode is not available. Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status. Operation (5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. Referring to the Fig. COOL About 10o Up and down (Use remote controller) Left and right air flow adjustment Press SWING button, vertical flap will move within(manual) the range shown in the Fig. Press SWING button Move the horizontal blade by a knob on air conditioner to adjust left and right direction stop it at a fixed position. referring to Fig. About 10o COOL About 45o Cautions: It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur. Cautions: When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right. (6) Unit stop Press ON/OFF button. Vertical flap closes automatically. Cautions: Unit won't restart until 3 minutes have elapsed, due to system protection. [. . . ] Don't use glass cleaner or cloth soaked with chemicals. A rF l e i itr 1. Open inlet grille by pulling it upward. 2. Remove air filter Push up the filter's center tab slightly until it is caesura of 3. Clean the filter the stopper. cleaner to remove dust, or wash the filter with water. After washing, dry the filter 4. Attach the filter completely in the shade. [. . . ]