User manual HAIER HSU-07CG03/R1

[. . . ] MODE Used to select AUTO, COOL, DRY , HEAT and FAN 11. TIMER Used to select TIMER ON, TIMER OFF 13. RESET Used to reset the controller back to normal condition 14. CODE Used to select code A or B with a press, A or B will be displayed on LCD. please select A without special explanation 15. [. . . ] Press SWING button stop it at a fixed position. Left and right air flow adjustment (manual) Move the horizontal blade by a knob on air conditioner to adjust left and right direction referring to Fig. About 10o COOL About 45o Cautions: It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur. Cautions: When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right. (6) Unit stop Press ON/OFF button. Vertical flap closes automatically. Cautions: Unit won't restart until 3 minutes have elapsed, due to system protection. Hints As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. Be careful not to catch a cold when cold air blows downward. It is harmful to your health in summer to go frequently in and out of places where temp. difference of 3-5oC will remove your fatigue. More than this, unit's load can be reduced and power consumption cut down as well. diff of 3-5oC between indoor and outdoor temp. in COOL mode. 9 Operation TIMER operation Set Clock correctly before starting Timer operation(referring to page 5) You can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night. TIMER ON/OFF (1)After unit start, select your desired operation mode. Operation mode will be displayed on LCD. Power indicator on indoor unit lights up. A (2)TIMER mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: ON TIMER ON OFF TIMER OFF ON OFF blank TEMP TIMER ON-OFF SWING ON OFF 1 SLEEP FAN Select your desired TIMER mode (TIMER ON or TIMER OFF) ON or OFF will flash. MODE (3)Timer setting Press HOUR button. Every time the button is pressed, time increases 10 min. If button is kept depressed, time will change quickly. Every time the button is pressed, time decreases 10 min. If button is kept depressed, time will change quickly. It can be adjusted within 24 hours. CLOCK SET TIMER 4 3 2 RESET CODE LOCK (4)Confirming your setting After setting correct time, press SET button to confirm, "ON" or "OFF" stops flashing Time displayed: Unit starts or stops at x hour x min. Timer mode indicator on indoor unit lights up. To cancel TIMER mode Just press TIMER button several times until TIMER mode disappears. Hints After replacing batteries or a power failure happens, Time setting should be reset. Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if timer setting is the same as previous one. 10 Operation TIMER ON-OFF (1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. Power indicator on indoor unit lights up. (2) Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: ON TIMER ON OFF TIMER OFF ON OFF blank A TIMER ON-OFF Select TIMER ON-OFF. "ON" will flash. (3)Time setting for TIMER ON Press HOUR button. Every time the button is pressed, time increases 10min. If button is kept depressed, time will change quickly. [. . . ] Should there be a big noise from air flow in unit operation, air filter may be too dirty. This is because the system circulates smells from the interior air such as the smell of furniture, cigarettes. During COOL or DRY operation, indoor unit may blow out mist. This is due to the sudden cooling of indoor air. Noise is heard : Normal performance inspection Smells are generated. Mist or steam are blown out. Does not work at all. [. . . ]