User manual HAIER HSU-09HB03/R2

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU-07HB03/R2 HSU-09HB03/R2 HSU-12HB03/R2 HSU-14HB03/R2 HSU-18HB03/R2 HSU-22HB03/R2 HSU-22HC03/R2 H2SM-14HB03/R2 H2SM-18HB03/R2 Please read this operation manual before using the air conditioner. No. Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner Consult your local authorities for the name and address of the waste materials collecting in order to avoid the risk of child entrapment. centers and waste paper disposal services nearest to your house. [. . . ] The distance between the signal transmission head and the receiver hole should be within 7 m without any obstacle as well. Don't throw the controller, prevent it from being damaged. When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter. Loading of the battery Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder) Remove the battery cover: Slightly press " " and push down the cover. Load the battery: Be sure that the loading is in line with the" + "/"-" pole request as illustrated. Put on the cover again Confirmation indicator: In disorderation, reload the batteries or load the new batteries after 6 mins. Note: Use two new same-typed batteries when loading. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. Use COOL in summer. Use HEAT in winter Use DRY in spring, autumn and in damp climate. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN Unit will run in operation mode displayed on LCD. Stop display at your desired mode. (3) Select temp. o Every time the button is pressed, temp. setting increases 1 C o Every time the button is pressed, temp. setting decreases 1 C Unit will start running to reach the temp. setting on LCD. (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: LO MED HI AUTO COOL operation starts when room temp. setting. Ultra-low air flow Unit runs at the speed displayed on LCD. In HEAT mode, warm air will blow out after a short period of time due to cold-draft prevention function. setting, unit will run intermittently at LO speed regardless of FAN setting. Temp. setting, unit will run in mild DRY mode. Hints On cooling only unit, heating mode is not available. Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status. 10 Operation (5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. Referring to the Fig. COOL About 10 o HEAT About 60o Left and right air flow adjustment Press SWING button, vertical flap will move within (manual) Up and down (Use remote controller) the range shown in the Fig. Press SWING button stop it at a fixed position. Move the horizontal blade by a knob on air conditioner to adjust left and right direction referring to Fig. About 10o COOL About 45o HEAT About 60o Cautions: It is advisable not to keep vertical flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur. Cautions: When humidity is high, condensate water might occur at air outlet if all horizontal louvers are adjusted to left or right. (6) Unit stop Press ON/OFF button. Vertical flap closes automatically. Cautions: Unit won't restart until 3 minutes have elapsed, due to system protection. [. . . ] After washing, dry the filter completely in the shade. 2. Remove air filter Push up the filter's center tab slightly until it is caesura of the stopper. Remove it by pulling down. 5. Close the inlet grille. 4. Attach the filter Attach filter behind the stopper so that the "Front" indication is facing to the front. Make sure that it is completely behind the stopper, otherwise problems might occur. 17 Maintenance Replacement of Purifying Filter 1 Open the Inlet Grille Open the inlet grille by pushing each end of the inlet grille upward. 2 Detach the standard air Filter Slide the knob slightly upward to release the filter, then withdraw it. 3 Detach the Air Purifying Filter Replace old Air Purifying Filter with new one into the frame. Air Filter 4 Attach the Air Purifying Filter Attaching each of the Air Purifying Filters to the indoor unit as white side face to front. For the units of 22, the purifying filter is put into the standard filter. Air Purifying Filter 5 Attach the standard air Filter (make sure to be attached) Operating without standard air filter may cause trouble with the machine. 6 Close the inlet Grille Close the Grille surely. [. . . ]