User manual HAIER HSU-09HD03/R2

[. . . ] 9. Young children should be supervised ensure that they do not play with the appliance. 10. The appliance must be installed on strong enough supporter. 11. The wiring diagram is attached inside the machine. Air Conditioner Edition:2006/1/10 Parts and Functions Indoor Unit Inlet grille Test running switch(manual) Used only for test running in cooling when room temp. Don't use it in normal operation. Emergency switch(manual) Used when remote controller is lost or defective. [. . . ] For each press, operation mode changes as follows: ON/OFF TEMP 1 4MODE 2 FAN SET AUTO COOL DRY HEAT FAN TIMER Unit will run in selected mode. Stop display at " " AUTO or " 3 "FAN. SWING CLOCK (3) FAN Press FAN button. For each press, fan speed changes as follows: SLEEP LOCK RESET AUTO LO MED HI (4) Unit stop Unit will run at selected fan speed. Vertical flap closed automatically. Hints Remote controller can memorize settings in each operation mode. To run it next time just select the operation mode and it will start with the previous setting. No reelecting is needed. (TIMER ON/OFF needs reelecting) Cautions: Note: On cooling only unit, heating mode is not available, The above information is the After replacing batteries, press ON/OFF, and display explanation of the displayed becomes as follows: information therefore varies Operation mode: AUTO, Temp. No with those displayed in actual Timer mode: No, Fan speed :AUTO operation. Air Conditioner Edition:2006/1/10 Operation COOL, HEAT and DRY operation Recommendations: (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. Use COOL in summer. Use HEAT in winter Use DRY in spring, autumn and in damp climate. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: ON/OFF TEMP AUTO COOL DRY HEAT FAN 6 1 3 3 SET MODE Unit will run in operation mode displayed on LCD. Stop display at your desired mode. (3) Select temp. o Every time the button is pressed, temp. setting increases 1 C o Every time the button is pressed, temp. setting decreases 1 C Unit will start running to reach the temp. setting on LCD. 2 FAN TIMER 4 SWING CLOCK 5 SLEEP (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: LOCK RESET AUTO LO MED HI COOL operation starts when room temp. setting. Ultra-low air flow Unit runs at the speed displayed on LCD. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. Temp. setting, unit will run in mild DRY mode. Hints On cooling only unit, heating mode is not available. Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status. Air Conditioner Edition:2006/1/10 Operation (5) Air flow direction adjustment After operation mode is selected, vertical flap will open automatically according to the mode. COOL About 10 o HEAT About 60o Up and down (Use remote controller) Left and right air flow adjustment Press SWING button, vertical flap will move within (manual) the range shown in the Fig. [. . . ] In FAN mode, comfortable sleep is not available. SLEEP mode starts SLEEP mode stops Fig. 2 Air Conditioner Edition:2006/1/10 Maintenance Different models have different appearance Cleaning of unit casing Cut off power supply before cleaning unit casing with soft cloth. In case of heavy stain, clean it with neutral detergent. squeeze water in the cloth, wipe off the detergent on unit casing completely. Cleaning of remote controller Cleaning of air filter Don't use water to wash unit casing, please use dry cloth. Don't use glass cleaner or cloth soaked with chemicals. Air Filter 1. Open inlet grille by pulling it upward. 3. Clean the filter Use a vacuum cleaner to remove dust, or wash the filter with water. [. . . ]