User manual HAIER HSU-09LEA13-H

[. . . ] The type of connecting wire is H05RN-F or H07RN-F 3. If the fuse on PC board is broken please change it with the type of T. The distance between the indoor unit and the floor should be more than 2m. The wiring method should be in line with the local wiring standard. [. . . ] When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter. Loading of the battery Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder) Remove the battery cover: Slightly press " " and push down the cover. ¡/ TM ¨"ª ±, OE °"Õ ª" «Î-- ±º ÿ»° 7# ÿ, § ´µÁ Î `Y £, « µÁ ¬©"«Î Á"^"Ï ÷÷"Û ¿÷ ^, 6 ^°£ ÿ»° `/ "÷­» ÿ°£ ´µÁ ¬µÁ µ£° æ »Î­ Õ« fi<´À £°ºØ ~"­oe ø'µ~ «Î--°"Õ¨"ª¡/ 7# µÁÿ, § ±ºª" ±, OETM ¿÷¬©"«Î´µÁÿ»° ^°£ `/ "÷­»Á"^"Ï£, «Î ´µÁÿ»°^, 6÷÷"Û`Y »Î­¬µÁÿ°£ £°ºØÕ«µ£° ø'µ~~"­oefi<´Àæ «Î--°"Õ¨"ª¡/ 7# µÁÿ, § ±ºª" ±, OETM ¿÷¬©"«Î´µÁÿ»° ^°£ `/ "÷­»Á"^"Ï£, «Î ´µÁÿ»°^, 6÷÷"Û`Y »Î­¬µÁÿ°£ £°ºØÕ«µ£° ø'µ~~"­oefi<´Àæ Load the battery: Be sure that the loading is in line with the" + "/"-" pole request as illustrated. Put on the cover again Confirmation indicator: In disorderation, reload the batteries or load the new batteries after 6mins. Note: Use two new same-typed batteries when loading. If the remote controller can't run normally or doesn't work at all, use a sharp pointed item to press the reset key. Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out just need to press reset key. Power failure resume(please set and apply as necessary) If sudden power failure occurs, the unit will resume original operation when power is supplied again. Note: When sudden power failure happens during unit operation in power failure resume mode, if the air conditioner is not desired for use in a long period, please shut off the power supply in case that the unit automatically resume operation when power is re-supplied, or press ON/OFF to turn off the unit when power resumes. 5 Operation Auto run, Fan operation (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. Enjoy yourself by just a gentle press. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: ON/OFF TEMP 1 4MODE SET AUTO COOL DRY HEAT FAN 2 FAN TIMER Unit will run in selected mode. Stop display at " " AUTO or " 3 "FAN. SWING CLOCK (3) FAN Press FAN button. For each press, fan speed changes as follows: SLEEP LOCK RESET AUTO LO MED HI (4) Unit stop Unit will run at selected fan speed. Vertical flap closed automatically. Hints Remote controller can memorize settings in each operation mode. To run it next time just select the operation mode and it will start with the previous setting. Be careful not to catch a cold when cold air blows downward. It is harmful to your health in summer to go frequently in and out of places where temp. difference of 3-5 C will remove your fatigue. More than this, unit's load can be reduced and power consumption cut down as well. difference of 3-5 C between indoor and outdoor temp. in COOL mode. 8 Operation TIMER Operation Set Clock correctly before starting Timer operation You can let unit start or stop automatically at following times: Before you wake up in the morning, or get back from outside or after you fall asleep at night. TIMER ON/OFF (1)After unit start, select your desired operation mode. Operation mode will be displayed on LCD. Power indicator on indoor unit lights up. (2)TIMER mode selection Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: ON TIMER ON OFF TIMER OFF ON OFF blank ON/OFF TEMP TIMER ON-OFF MODE Select your desired TIMER mode (TIMER ON or TIMER OFF) ON or OFF will flash. 1 SET 3 FAN 4 TIMER (3)Timer setting Press HOUR / button. Every time the button is pressed, time increases 10 min. If button is kept depressed, time will change quickly. [. . . ] When the power resumes after power failure, the unit will run automatically, the power indicator lights up, and 3 minutes later the compressor starts running with the indicator lighting up. Fig. 1 Temp. setting decreases 2oC decreases 2oC Unit stop 1 hr 1 hr Approx. 3 hrs 3 hrs Rises 1oC Note: In AUTO mode, unit will run in SLEEP function according to operation mode. In FAN mode, comfortable sleep is not available. SLEEP mode starts SLEEP mode stops Fig. 2 12 Maintenance Different models have different appearance Cleaning of unit casing Cut off power supply before cleaning unit casing with soft cloth. [. . . ]