User manual HAIER HSU-12CG13-B

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL AMS12H03 AMS18H03 AMS22H03 HSU-09CG13-B HSU-12CG13-B HSU-18CG13-B HSU-24CG13-B Please read this operation manual before using the air conditioner. 0010518054 Cautions The machine is adaptive in following situation I. Applicable ambient temperature range: Indoor Cooling Outdoor Indoor Heating Outdoor Maximum: D. B / W. B Minimum: D. B / W. B Maximum: D. B Minimum: D. B Maximum: D. B Minimum: D. B Maximum: D. B / W. B Minimum: D. B / W. B 32 C/23 C o o 18 C/14 C o o 43 C/26 C o 18 C o 27 C o 15 C o o 24 C/18 C o o -7 C/-8 C o o 2. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. The type of connecting wire is H05RN-F or H07RN-F 3. [. . . ] To run it next time just select the operation mode and it will start with the previous setting. No reelecting is needed. (TIMER ON/OFF needs reelecting) Cautions: Note: On cooling only unit, heating mode is not available, The above information is the After replacing batteries, press ON/OFF, and display explanation of the displayed becomes as follows: information therefore varies Operation mode: AUTO, Temp. No with those displayed in actual operation. 6 Operation COOL, HEAT and DRY operation Recommendations: (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. Use COOL in summer. Use HEAT in winter Use DRY in spring, autumn and in damp climate. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: ON/OFF TEMP AUTO COOL DRY HEAT FAN 6 2 FAN TIMER 1 Unit will run in operation mode displayed on LCD. Stop display at your desired mode. 3 3 SET MODE (3) Select temp. o Every time the button is pressed, temp. setting increases 1 C o Every time the button is pressed, temp. setting decreases 1 C Unit will start running to reach the temp. setting on LCD. 4 SWING CLOCK 5 SLEEP (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: LOCK RESET AUTO LO MED HI COOL operation starts when room temp. setting. Ultra-low air flow Unit runs at the speed displayed on LCD. setting, unit will run intermittently at LO speed regardless of FAN setting. o Temp. setting, unit will run in mild DRY mode. Hints On cooling only unit, heating mode is not available. Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status. 7 Operation (5) Air flow direction adjustment After operation mode is selected, horizontal flap will open automatically according to the mode. COOL About 10 o HEAT About 60o Left and right air flow adjustment Press SWING button, horizontal flap will move within (manual) the range shown in the Fig. Press SWING button stop it at a fixed position. Up and down (Use remote controller) Move the vertical blade by a knob on air conditioner to adjust left and right direction referring to Fig. About 10o COOL About 45o HEAT About 60o It is advisable not to keep horizontal flap at downward position for a long time in COOL or DRY mode, otherwise, condensate water might occur. Cautions: Cautions: When humidity is high, condensate water might occur at air outlet if all vertical louvers are adjusted to left or right. (6) Unit stop Press ON/OFF button. Horizontal flap closes automatically. Cautions: Unit won't restart until 3 minutes have elapsed, due to system protection. HEAT mode is not available on cooling only unit. Hints As cold air flows downward in COOL mode, adjusting air flow horizontally will be much more helpful for a better air circulation. As warm air flows upward in HEAT mode, adjusting air flow downward will be much more helpful for a better air circulation. [. . . ] After washing, dry the filter completely in the shade. 2. Remove air filter Push up the filter's center tab slightly until it is caesura of the stopper. Remove it by pulling down. 5. Close the inlet grille. 4. Attach the filter Attach filter behind the stopper so that the "Front" indication is facing to the front. Make sure that it is completely behind the stopper, otherwise problems might occur. 14 Maintenance Replacement of Air Purifying Filter NOTE: Air purifying filter is optional part 1. Open the lnlet Grille Open the inlet grille by pushing each ends of the inlet grille upward. (use thumbs to push up) 2. Detach the standard air filter Slide the knob slightly upward to release the filter, then withdraw it. 3. Detach the Air Purifying Filter Replace the old filter with new one into the frame. 4. Attach new Air Purifying Filter Attaching each of the Air Purifying Filter to the indoor unit as its white side faces to the front . 5. Attach the standard air filter as its front side faces to the front Operating without standard air filter may cause troubles with the machine. 6. Close the Inlet Grille Close the Grille surely NOTE: Please replace the air Purifying Filter when color of the filter become same levle of sample attached in the indoor unit. Please replace the air Purifying Filter in 3-6 months as standard. [. . . ]