User manual HAIER HSU-12RH03/R2

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU-09RH03/R2 HSU-12RH03/R2 HSU-18RH03/R2 HSU-22RH03/R2 H2SM-(9+9)RH03/R2 Please read this operation manual before using the air conditioner No. 0010562103 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require specialized waste disposal. The valuable materials contained in an air conditioner can be recycled . Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. [. . . ] If there are any display after taking-out, just need to press reset key. 7 Operation HEALTH operation Remote controller 1. Unit start Press ON/OFF on the remote controller, unit starts. 2. Health anion function Press HEALTH button. Air conditioner starts health anion function operation. For twice press, disappears, the operation stops. When indoor fan motor is running, it has healthy process function. (It's available under any mode) BRIEF INTRODUCTION TO HEALTH ANION FUCTION The anion generator in the air conditioner can generate a lot of anion effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room. 8 Operation Auto Operation Remote controller 1. Unit start Press ON/OFF on the remote controller, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select Auto operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1oC, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting decrease 1oC, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. 5. Unit stop Press ON/OFF button, the unit stops. 11 Operation Fan Operation 1. Unit start Press ON/OFF on the remote controller, unit starts. Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select FAN operation 3. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI 4. Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the unit will not operate in COOL or HEAT mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP operation is not available. 12 Operation Heat Operation 1. Unit start Press ON/OFF on the remote controller, unit starts. Remote controller 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN HEAT Then Select HEAT operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1oC, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting decrease 1oC, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI AUTO Air conditioner is running under displayed fan speed IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 13 Operation Air Flow Direction Adjustment 1. Status display of air sending Vertical flap Pos. 1 Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Horizontal louvers (Auto swing) Pos. 6 Pos. 7 Pos. 8 2. Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 6 remote controller: : HEAT: remote controller: AUTO: remote controller: Pos. 5 Pos. 4 Pos. 3 Pos. 2 Pos. 1 Pos. 6 Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 The vertical flap will swing according to the above positions 3. Left and right air flow direction For each press of remote controller: Pos. 1 Pos. 2 Pos. 3 button, remote controller displays as follows : Pos. 4 Pos. 5 Pos. 6 Pos. 7 Pos. 8 The horizontal louvers will swing according to the above positions. Note:When restart after remote turning off, the remote controller will automatically memorize the previous set swing position. 14 Operation Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. Use of SLEEP function After the unit starts, set the operation status, then press SLEEP button before which the clock must be adjusted and time being set. In COOL, DRY mode 1 hours after SLEEP mode starts, temp. The unit will run for further 6 hours then stops. [. . . ] Remove the filter. Push up the filter's center tab slightly until it is released from the stopper, and remove the filter downward. Clean the filter. Use a vacuum cleaner to remove dust, or wash the filter with water. After washing, dry the filter completely in the shade. Attach the filter. Attach the filter correctly so that the "FRONT" indication is facing to the front. Make sure that the filter is completely fixed behind the stopper. If the right and left filters are not attached correctly, that may cause defects. Once every two weeks Close the inlet grille. 21 Maintenance Replacement of Air Purifying Filter 1. Open the lnlet Grille Open the inlet grille by pushing each ends of the inlet grille upward. (use thumbs to push up) 2. Detach the standard air filter Slide the knob slightly upward to release the filter, then withdraw it. 3. Detach old Air Purifying Filter 4. Attach old Air Purifying Filter Put air purifying filter appliances into the right and left filter frames . Detach old Air Purifying Filter 5. Attach the standard air filter (Necessary installation) 6. Close the Inlet Grille Close the Grille surely NOTE: The air purifying filter of the bacteria-killing medium and the electrostatic air purifying filter accessories with machine will be used based on real situation. The bacteria-killing medium air purifying filter is available for a long time and needn't to be changed. But it must be noticed to use the vacuum cleaner frequently to adsorb the dusts covering the purifying filter lest the covering dusts effect the function of the bacteria-killing medium air purifying filter. [. . . ]