User manual HAIER HSU-14CR13

[. . . ] SPLIT TYPE ROOM AIR CONDITIONER OPERATION MANUAL HSU-09CR13 HSU-12CR13 HSU-14CR13 Please read this operation manual before using the air conditioner No. 0010562469 Cautions Disposal of the old air conditioner Before disposing an old air conditioner that goes out of use, please make sure it's inoperative and safe. Unplug the air conditioner in order to avoid the risk of child entrapment. It must be noticed that air conditioner system contains refrigerants, which require speciali-zed waste disposal. The valuable materials contained in an air conditioner can be recycled Contact your local waste disposal center for proper disposal of an old air conditioner and contact your local authority or your dealer if you have any question. [. . . ] 2. The purification function of AIP: DC high voltage bring high voltage electrostatic field, which ionize air into positive and negative ion. a great deal of positive and negative ion adhere to dust passing by, so the dust become "particle with electric charge". When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. 5. Unit stop Press ON/OFF button, the unit stops. 10 Operation Display board Dry Operation Remote controller 1. Unit start Press ON/OFF on the remote controller, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN Then Select DRY operation 3. Select temp. setting Press TEMP. button Every time the button is pressed, temp. setting increase 1oC, if kept depressed, it will increase rapidly Every time the button is pressed, temp. setting decrease 1oC, if kept depressed, it will decrease rapidly Select a desired temperature. 4. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW COOL operation starts when room temp. is higher than temp. setting. Temp. setting+2oC Temp. setting On reaching temp. setting +2oC unit will run in mild DRY mode. MED HI AUTO Ultra-low air flow Air conditioner is running under displayed fan speed. In DRY mode, when room temperature becomes lower than temp. setting+2oC, unit will run intermittently at LOW speed regardless of FAN setting. 5. Unit stop Press ON/OFF button, the unit stops. 11 Operation Display board Fan Operation 1. Unit start Remote controller Press ON/OFF on the remote controller, unit starts. 2. Select operation mode Press MODE button. For each press, operation mode changes as follows: Remote controller: AUTO COOL DRY FAN Then Select FAN operation 3. Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: LOW MED HI 4. Unit stop Press ON/OFF button, the unit stops. About FAN operation In FAN operation mode, the unit will not operate in COOL mode but only in FAN mode , AUTO is not available in FAN mode. And temp. setting is disabled. In FAN mode, SLEEP operation is not available. 12 Operation Air Flow Direction Adjustment 1. Status display of air sending Horizontal louvers Vertical flap Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 4 Pos. 5 Pos. 5 Pos. 6 Pos. 6 Pos. 1 Pos. 2 Pos. 3 wall-mounted type (Auto swing) Pos. 7 Pos. 8 2. Up and down air flow direction For each press of button, air flow direction on remote controller displays as follows according to different operation modes: COOL/DRY/FAN Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 6 remote controller: : AUTO: remote controller: Pos. 1 Pos. 2 Pos. 3 Pos. 4 Pos. 5 Pos. 6 The vertical flap will swing according to the above positions 3. Left and right air flow direction For each press of remote controller: Pos. 1 Pos. 2 Pos. 3 button, remote controller displays as follows : Pos. 4 Pos. 5 Pos. 6 Pos. 7 Pos. 8 The horizontal louvers will swing according to the above positions. Note:When restart after remote turning off, the remote controller will automatically memorize the previous set swing position. 13 Operation Display board Sleep Operation Before going to bed, you can simply press the SLEEP button and unit will operate in SLEEP mode and bring you a sound sleep. Use of SLEEP function After the unit starts, set the operation status, then press SLEEP button before which the clock must be adjusted and time being set. In COOL, DRY mode 1 hours after SLEEP mode starts, temp. The unit will run for further 6 hours then stops. setting so that room temperature won't be too Iow for your sleep. SLEEP operation starts SLEEP operation stops Approx. 6hrs Rises 1OC 1 hr 1 hr Rises 1OC Temp. setting Unit stop In COOL, DRY mode Remote Controller 2. In AUTO mode The unit operates in corresponding sleep mode adapted to the automatically selected operation mode. 4. Set the wind speed change when sleeping If the wind speed is high or middle before setting for the sleep, set for lowing the wind speed after sleeping. If it is low wind, no change. 14 Operation Display board Timer On/Off Operation Remote Controller Set clock correctly before starting TIMER operation. After unit starts, select your desired operation mode Operation mode will be displayed on LCD. [. . . ] Please don't expose it to the sunlight for a long time otherwise the degerming performance will drop. 22 Maintenance To Keep Your Air conditioner in Good Condition after Season. 1. Operate in cooling mode for 2-3 hours. To prevent breeding mold or bad smell, be sure to O operate at the designated temperature or 30 C, cooling mode and High speed fan mode for 2-3 hours. 2. Take out the batteries from the wireless remote controller. 23 Maintenance Before Setting in High season 1. Cleaning the standard air filter. Operation without filter may cause troubles. Be sure to attach both right and left filters prior to the operation. [. . . ]