User manual HAIER HSU-14HB03

[. . . ] Please ensure that the pipework of your air conditioner does not get damagedprior to being picked up by the relevant waste disposal center, and contribute to environmental awareness by insisting on an appropriate, anti-pollution method of disposal. Safety Instructions and Warnings Before starting the air conditioner, read the information given in the User's Guide carefully. The User's Guide contains very important observations relating to the assembly, operation and maintenance of the air conditioner. The manufacturer does not accept responsibility for any damages that may arise due to non-observation of the following instruction. Damaged air conditioners are not to be put into operation. [. . . ] SET Used to confirm timer and clock settings. 21. TIMER FAN Used to select TIMER ON, TIMER OFF, TIMER ON-OFF 22. RESET Used to reset the controller back to normal condition. AUTO LO MED HI 2. Ambient temp. display When receiving the remote control signal, display the set temperature and in the rest time the room temperature is displayed and this room temperature is only for reference. Clock set When unit is started for the first time and after replacing batteries in remote controller, clock should be adjusted as follows: Press CLOCK button, "AM" or "PM" flashes. Each press will increase or decrease 1min. If the button is kept depressed, time will change quickly. After time setting is confirmed, press SET, "AM "and "PM" stop flashing, while clock starts working. NOTE: Cooling only unit do not have displays and functions related with heating. Hints: After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. 7 Operation Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well. Don't throw the controller, prevent it from being damaged. (Not Timer setting) (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: AUTO COOL DRY HEAT FAN ON/OFF TEMP Unit will run in operation mode displayed on LCD. Stop display at your desired mode. 5 2 FAN 1 3 3 SET MODE (3) Select temp. o Every time the button is pressed, temp. setting increases 1 C o Every time the button is pressed, temp. setting decreases 1 C Unit will start running to reach the temp. setting on LCD. TIMER 4 SWING CLOCK SLEEP HEALTH (4) Fan speed selection Press FAN button. For each press, fan speed changes as follows: Remote controller: AUTO LO MED HI LOCK RESET IN HEAT mode, warm air will blow out after a short period of the time due to cold-draft prevention function. When FAN is set to AUTO, the air conditioner automatically adjusts the fan speed according to room temperature. (5) Unit stop Press ON/OFF button, the unit stops. Hints Remote controller can memorize each operation status. When starting it next time, just press ON/OFF button and unit will run in previous status. 12 Operation Fan Operation (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) (2) Select operation mode Press MODE button. [. . . ] Use this switch in the test operation when the room o temperature is below 16 C, do not use it in the normal operation. Continue to press the test operation switch for more than 5 seconds. After you hear the "Pi" sound twice, release your finger from the switch: the cooling operation starts with the air flow speed "Hi". Pi Pi After 30 minutes, test operation ends automatically(Only for 22K or 24k unit). Removal of the restriction of emergency or test operation: Press the emergency operation switch once more, or manipulate through the remote controller; the "Pi" sound, the emergency or test operation is terminated. When the remote controller is manipulated, it gets the system back to the normal operation mode. 19 Maintenance For Smart Use of The Air Conditioner Setting of proper room temperature Proper temperature Do not block the air inlet or outlet Close doors and windows Use the timer effectively during operation During cooling operation prevent the penetration of direct sunlight with curtain or blind If the unit is not to be used Use the louvers effectively for a long time, turn off the power supply main switch. OFF 20 Maintenance For Smart Use of The Air Conditioner WARNING Before maintenance, be sure to turn off the system and the circuit breaker. Remote Controller Indoor Body Do not use water wipe the controller with a dry cloth. Do not use glass cleaner or chemical cloth. Wipe the air conditioner by using a soft and dry cloth. For serious stains, use a neutral detergent diluted with water. Wring the water out of the cloth before wiping. then wipe off the detergent completely. Do not use the following for cleaning Gasoline, benzine, thinner or cleanser may damage the coating of the unit. Hot water over 40 C(104 F) may cause discoloring or deformation. O O Air Filter cleaning Open the inlet grille by pulling it upward. [. . . ]