User manual HAIER HSU-18RC03R2

[. . . ] 10. The appliance must be installed on strong enough supporter. 11. The wiring diagram is attached inside the machine. 8. The appliance is not intended to use by young children or infirm persons without supervi Parts and Functions Parts and Functions Operation Buttons and display of the remote controller. 1. MODE Used to select AUTO run, COOL, DRY, HEAT and FAN operation 1 2 3 4 ON/OFF TEMP 5 6 7 8 9 10 AUTO LO MED HI 11 18 MODE SET Used for unit start and stop. 12 FAN TIMER 19 13. [. . . ] TIMER Used to select TIMER ON, TIMER OFF, TIMER ON-OFF 21. RESET Used to reset the controller back to normal condition. like the following figure: 1 2 3 4 ON/OFF TEMP 5 6 7 8 9 10 11 18 MODE SET 12 FAN TIMER 19 13 14 SWING CLOCK 20 15 SLEEP HEALTH 21 16 LOCK RESET 17 22 BRIEF INTRODUCTION TO HEALTH OPERATION The anion generator in the air conditioner can generate a lot of anion to effectively balance the quantity of position and anion in the air and also to kill bacteria and speed up the dust sediment in the room and finally clean the air in the room. NOTE: Cooling only unit do not have displays and functions related with heating Hints After replacing with new batteries, remote controller will conduct self-check, displaying all information on LCD. Then, it will become normal. Operation Remote controller's operation When in use, put the signal transmission head directly to the receiver hole on the indoor unit. The distance between the signal transmission head and the receiver hole should be within 7m without any obstacle as well. Don't throw the controller, prevent it from being damaged. When electronic-started type fluorescent lamp or change-over type fluorescent lamp or wireless telephone is installed in the room, the receiver is apt to be disturbed in receivering the signals so the distance to the indoor unit should be shorter. Loading of the battery Load the batteries as illustrated. 2 R-03 batteries, resetting key (cylinder) Remove the battery cover: Slightly press " " and push down the cover. / , OE TM Î Û ` Y « ± , " « Î 7# -- µ ° Á " ÷ ¿ ^°£ ` Õ ÿ / ¨ , ¬ ´ " © » ª µ " § Î "Á ­ £ ø « ¬ ± ÷ÿ ' µ Î º ° Á ­ µ ¡ ´ » » º ~ ÿ ° Ø µ Á ° ~ Õ ª Á " £ " " ^ ^ ­ « ÿ , " oe » fi Ï 6 µ ° < ÷ £ ÷ £´ À °æ / / TM OE Î Û , « ± ° Y ` , " £ ÷ » ÷ " ÿ ¡ ª Á ^ , ª"¨Õ"°--Ϋ 7# § , ÿ Á µ « " © ¬ ÷ ¿ ^°£ "Á»­÷" /` ^ ° » ÿ Á µ ´ £ ° ÿ Á µ ¬ ­ Î » £ ' ø TM OE Î Û , « ± ° Y ` , " £ ÷ " » ÷ ¡ ª Á ^ , º± µ´Î ÿ º± µ´Î Ï" 6 Ï" 6 ª"¨Õ"°--Ϋ 7# § , ÿ Á µ « " © ¬ ÷ ¿ ^°£ "Á»­÷" /` ^ ° » ÿ Á µ ´ £ ° ÿ Á µ ¬ ­ Î » £ ' ø ° ° £µ«Õغ° æ À ´ <fi oe ­ "~~µ £µ«Õغ° æ À ´ <fi oe ­ "~~µ Load the battery: Be sure that the loading is in line with the" + "/"-" pole request as illustrated. Put on the cover again Confirmation indicator: In disorderation, reload the batteries or load the new batteries after 6mins. Note: Use two new same-typed batteries when loading. If the remote controller can't run normally or doesn't work at all, use a sharp pointed item to press the reset key. Hint: Remove the batteries in case unit won't be in usage for a long period. If there are any display after taking-out just need to press reset key. Power failure resume(please set and apply as necessary) If sudden power failure occurs, the unit will resume original operation when power is supplied again. Note: When sudden power failure happens during unit operation in power failure resume mode, if the air conditioner is not desired for use in a long period, please shut off the power sup in case that the unit automatically resume operation when power is re-supplied, or press ON/OFF to turn off the unit when power resumes. Operation Auto run, Fan operation (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. (Not Timer setting) Power indicator on indoor unit lights up. Enjoy yourself by just a gentle press. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: ON/OFF TEMP MODE SET AUTO COOL DRY HEAT FAN FAN TIMER Unit will run in selected mode. Stop display at " " AUTO or " "FAN. SWING CLOCK (3) FAN Press FAN button. For each press, fan speed changes as follows: SLEEP LOCK RESET AUTO LO MED HI (4) Unit stop Unit will run at selected fan speed. Vertical flap closed automatically. Hints Remote controller can memorize settings in each operation mode. To run it next time just select the operation mode and it will start with the previous setting. No reelecting is needed. (TIMER ON/OFF needs reelecting) Cautions: Note: On cooling only unit, heating mode is not available, The above information is the After replacing batteries, press ON/OFF, and display explanation of the displayed becomes as follows: information therefore varies Operation mode: AUTO, Temp. No with those displayed in actual Timer mode: No, Fan speed :AUTO operation. Operation COOL, HEAT and DRY operation Recommendations: (1) Unit start Press ON/OFF button, unit starts. Previous operation status appears on display. Timer setting) (Not Power indicator on indoor unit lights up. Use COOL in summer. Use HEAT in winter Use DRY in spring, autumn and in damp climate. (2) Select operation mode Press MODE button. For each press, operation mode changes as follows: ON/OFF TEMP AUTO COOL DRY HEAT FAN MODE SET Unit will run in operation mode displayed on LCD. Stop display at your desired mode. (3) Select temp. [. . . ] Remote controller possesses memory function, when use TIMER mode next time, just press SET button after mode selecting if timer setting is the same as previous one. Operation TIMER ON-OFF (1)After unit start, select your desired operation mode Operation mode will be displayed on LCD. Power indicator on indoor unit lights up. (2) Press TIMER button to change TIMER mode. Every time the button is pressed, display changes as follows: ON TIMER ON OFF TIMER OFF ON OFF blank TIMER ON-OFF Select TIMER ON-OFF. "ON" will flash. (3)Time setting for TIMER ON Press HOUR button. Every time If button is Every time If button is the button is pressed, time increases 10 min. [. . . ]