User manual HAIER HW-12C03/R1

[. . . ] 5-7 Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Installation Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 10-12 Parts Name Front panel Air inlet (indoor side) Air outlet (indoor side) Air inlet (outdoor side) Operation panel HW-09CV03 HW-12C03/R1 1 Operation Guide Operation panel Auto swing switch Auto swing Temp. setting COOL Mode selection 6 OFF ON OFF LO fan HI fan 3 9 1 Test run LO cool HI cool Wait 3 minutes before restarting. Thermostat switch Mode selection switch 2 Operation Guide Auto swing switch Auto swing OFF ON When the switch is set to " ON ", vertical louver will swing from side to side, delivering gentle air thus making you feel very comfortable. When it is set to " OFF ", vertical louver will stop at position. Mode selection switch OFF LO fan HI fan <1> <2> <3> <4> <5> LO cool HI cool Mode switch controls the fan motor speed. When set to "HI fan", fan motor runs at high speed to blow out strong air. When set to "LO fan", fan motor runs at low speed to blow out gentle air. When set to "HI cool", air-con will start speedy cooling, blowing out strong air. When set to "LO cool", air-con will start cooling at low speed , blowing out gentle air. When set to "OFF", air conditioner stops running. Hint When mode selection switch is shifted to "HI fan" or"LO fan", air-con will only blow out air without cooling. Problems may occur if unit is installed in the following places: Place where oil exists in the air including engine oil or seaside with salt breeze blowing and hot spring area with sulphureous gas in the air. 8 Trouble Shooting Phenomenon Check the unit Is plug firmly inserted?Resolution Readjust power supply or replace fuse. Doesn't work Is thermostat switch wrongly adjusted? Readjust the thermostat. Is direct sunlight in the room?Is mode selection switch set to "Hi fan" or "Lo fan"?Are there any obstacles blocking air inlet and outlet? Use curtain or blind. No cool air or poor cooling Shut doors and windows. Remove the obstacles. Is there too much heat source in the room? Remove the heat source. Is air filter clogged? Clean it. If problems can not be solved please pull out power plug and contact your dealer. 9 Installation instruction The installation of air conditioner(only for reference) 1, Make the wall hole or window hole(see Fig. 1) A HW-09CV03 HW-12C03/R1 350 B 530 Iron bracket 2, Fix the prefabricated iron bracket to stable positin by expansible screws. Depth of the wall Fig. 1 3, Take out the conditioner and accessories from the package. Condenser 4, Lift the back of the machine body silghtly . You can see the drain hole at the back of the bottom plate. Plug the black rubber lid of the enclosed accessories into the hole(see Fig. 2). Fig. 2 5, Plug the drain elbow of the enclosed accessories(with seal ring)into the drain hole on the vertical wall at the back of the bottom plate (see Fig. 3). Rubber lid 6, If you need to lead the condensed water to indicated position, pleae purchase a piece of plastic pipe with inner diameter of 16, set it on the drain elbow and tie it tightly. Drain elbow Drain hose Fig. 3 7, After installation of all the accessories, put the whole machine on the iron bracket . If there is drain hose , lead the hose to needed position (see Fig. 4). 11 Installation instruction Wall 8, Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to prevent the entering of outer noise and the leaking of the coolness. 9, After installation of the conditioner , insert the power plug into the outlet and perform test-run. Fig. 4 Drain hose The machine is adaptive in following situation 1. [. . . ] Fig. 2 5, Plug the drain elbow of the enclosed accessories(with seal ring)into the drain hole on the vertical wall at the back of the bottom plate (see Fig. 3). Rubber lid 6, If you need to lead the condensed water to indicated position, pleae purchase a piece of plastic pipe with inner diameter of 16, set it on the drain elbow and tie it tightly. Drain elbow Drain hose Fig. 3 7, After installation of all the accessories, put the whole machine on the iron bracket . If there is drain hose , lead the hose to needed position (see Fig. 4). 11 Installation instruction Wall 8, Fill any distance between the wall hole and the machine body with flexible sponge rubber strip to prevent the entering of outer noise and the leaking of the coolness. 9, After installation of the conditioner , insert the power plug into the outlet and perform test-run. Fig. 4 Drain hose The machine is adaptive in following situation 1. Applicable ambient temperature range: Maximum: Minimum: Maximum: Minimum: D. B/W. B D. B/W. B D. B/W. B D. B 32°C/23°C 18°C/14°C 43°C/26°C 18°C Indoor side Cooling Outdoor side 2. [. . . ]