User manual HAIER HW-12LN03

[. . . ] Select operation mode Press MODE button. For each press, operation mode FAN COOL DEHUM changes as follows: Then select COOL operation. When the COOL display lights bright, the unit will be working under the cooling function. FAN SPEED 3. [. . . ] Stop COOL operation starts when room temp. is higher than temp. setting. FAN SPEED Ultra-low air flow Temp. setting+2 C Temp. setting On reaching temp. setting +2 C unit will run in mild DRY mode. The compressor may cycle for 10 minutes on and 6 minuters off in Dehumid mode. 5 FAN operation 1. Select operation mode Press MODE button. For each press, operation mode changes as follows: FAN COOL DEHUM Then select FAN operation. When the FAN display lights bright , the unit will be working under the fan operation. In some days you may want to run the FAN function. Press the FAN button. 4 FAN SPEED 3. Fan speed selection Here the fan runs only at HIGH or LOW speed. Stop Press POWER button again. E-S FAN SPEED 4 6 ENERGY SAVER operation 1. Select operation mode Press MODE button. For each press, operation mode changes as follows: FAN COOL DEHUM Then select COOL operation. 4 FAN SPEED When the COOL display lights bright, the unit will be working under the COOL function. Saving energy function only can be used when A/C working on cooling condition. ENERGY SAVER selection When this function is selected, the fan will shut off three minutes after the compressor cycles off. This will reduce energy consumption and noise. When the compressor turns back on, the fan will turn on at the same time. If this function is not selected, the fan will not shut off when the compressor cycles off. 4. Stop Press POWER button again. E-S FAN SPEED 3 4 7 On cool On Off 24 On Off 24 Press "On"of remote controller or "TIMER" of control panel, Off Press "Off "of remote controller or "TIMER"of control panel, TIMER ON restarted mode FAN SPEED FAN SPEED E-S 8 Power failure resume(please set and apply as necessary) If sudden power failure occurs, the unit will resume original operation when power is supplied again. Note: When sudden power failure happens during unit operation in power failure resume mode, if the air conditioner is not desired for use in a long period, please shut off the power supply in case that the unit automatically resume operation when power is re-supplied, or press POWER to turn off the unit when power resumes. Operation Adjusting of the air direction Airflow Direction Vane The Vertical Airflow Direction Vane is manually controlled by positioning the vane todischarge the air upward, downward or straight out. [. . . ] (available on the market). (Refer to P15 for choosing these two modes. ) Fig. 1 Outlet pipe fitting Fig. 2 Rubber lid Back hole Rubber lid Bottom plate hole Back hole Outlet pipe fitting Bottom plate hole Cautions Power cord: Be sure to use the exclusive power cord. Change installation place: If air-con need to be changed to another place please contact the dealer, who sold you the unit. 12 13 Name Manual Battery (R-03 dry battery) Outlet Sealed gasket pipe fitting Rubber lid Screw Remote controller Figure Quantity 1 2 1 1 1 3 1 14 MODEL HW-09LN03 HW-12LN03 366mm 392mm 481mm 610mm outlet pipe fitting outlet pipe fitting outlet pipe fitting 15 Wiring Diagram WIRING DIAGRAM RECEIVING HEAD CON1 0010511621 M C R COMPRESSOR S FAN MOTOR LOUVER MOTOR BR M B BL M BR OR B B CAPACITOR PROTECTOR H ML R BL BL R BL CN3 CN12 CN13 CN11 CN8 CN9 CN10 CN14 TEMP. SENSOR CN2 3 COMP. RELAY 4 FUSE 250V/3. 15A BR Y/G BL POWER SUPPLY R:RED OR:ORANGE B:BLACK BR:BROWN BL:BLUE Y/G:YELLOW/GREEN NOTE:1. Because of different compressor, the dotted part may not be used. 2. There are no dotted lines on some types. [. . . ]