User manual HAIER HW-18CUA03

[. . . ] The wiring method should be in line with the local wiring standard. OPERATION CONDITIONS Applicable ambient temperature range: Cooling Max. Temperture: Min. Temperture: 1. ON/OFF Press it to start unit and press it again to stop. 2. ENERGY SAVER This will not only save you electrical and energy costs but also shuts off the unnecessary noise of the fan motor running. 4. FAN SPEED Used to select desired fan speed. 7. FUNCTION Used to select operation mode: A/C, DEHUMID, FAN. [. . . ] (Electrify for the first time) b) Set desired number by pressing the (+) pad of the Temp/Time buttons. If you passed the desired time, use the (-) pad key to lower the selection. "H" light is on the time is shown. "" light is on the temperature is shown. When using the timer the unit will use/revert to the last A/C, fan settings when activated. The timer must be reset every time you choose to use it. Machine body Front panel Machine body 1 Ventilation Air outlet (indoor side) (For model HW-18CU03 HW-18CUA03 only) 1. Start Press ON/OFF button. 2. Select operation mode If you need to only remove the moisture press the Dehumid button . Unit may run intermittently in Dehumid mode with fan speed at "LO", regardless of its setting . Air blown out will be very cold at relatively low room temp. Air inlet (outdoor side) CLOSE OPEN Air filter (inside) Air inlet (indoor side) Control panel The ventilation lever must be CLOSE position in order to maintain the best cooling conditions. When fresh air is necessary in the room, set the ventilation lever to the OPEN position. The damper is opened and room air is exhausted. SLEEP operation 1. Start unit and confirm its operation mode . In Dehumid and fan mode , there is no sleep function . 2. Select SLEEP function Press the SLEEP button one time , sleep can be done , Press the button for a second time , the setting is cancelled. Sleep lets you preset the unit to shut off in 8 hours . The setting of time is as below : 2 Air filter cleaning When dirt accumulates on air filter, air circulation will be blocked, which causes poor cooling. It is advisable to clean air filter every two weeks for longer operation. Take out the air filter 1. Loose the air inlet by pushing "PUSH" at both edges as shown. Clean the filter CAUTION Before cleaning, turn off the power. Do not circumgyrate the front panel any more than 90° to the unit or damage to the tabs may occur. PUSH 3 Airflow Direction Airflow Direction Vane The Vertical Airflow Direction Vane is manually controlled by positioning the vane to discharge the air upward, downward or straight out. Air filter(inside) In sleep running , the air velocity can be adjusted . After the sleep finishes , the air conditioner will resume its former mode automatically . In Sleep function , temp. setting will rise automatically by 1 after one hour's cooling operation . One hour later , it will rise by another 1 and maintain at this temp . until the unit runs for approx. 6 hours. 1. Gently flap the dirt off the air filter. [. . . ] Open the Air inlet geille , fix the front panel to the chassis firmly with the accessorial screw. (see Fig. 2 or Fig. 3) (NOTE:Your model will be the same as one of the right two illustrations, not both. ) 5. After installation of the conditioner, insert the power plug into the outlet and perform test-run. Wall Baby has gone sleep, better to adjust suitable temp. Water outlet flexible pipe(provide by user) 4 AIR CONDITIONER INSTALLATION (ONLY FOR REFERANCE) SELECTION OF THE INSTALLATION POSITION 1, The air-conditioner is better installed in shadow or in a place with short period of sunshine. In case the air-conditioner is installed at the point exposed directly to the sunshine, it should be protected from the direct sunlight as possible in order to avoid the long time of direct sunlight otherwise its performance will be lowered. For the convenience of operation, it is recommended that air-conditioner be installed at least at the height of 760-1300 mm above the floor and no obstacles before it for a free airflow. [. . . ]