User manual HAIER HW-18CVA03

[. . . ] Do not switch off the unit by pulling out the power plug. 5. Do not insert sticks, fingers or other objects into the unit. 6. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similar qualified person. 7. After installation, the power plug should be easily reached. [. . . ] setting COOL Mode selection 6 LO fan 9 OFF 3 HI fan 1 Test run LO cool HI cool Wait 3 minutes before restarting. The ventilation lever must be CLOSE position in order to maintain the best cooling conditions. When fresh air is necessary in the room, set the ventilation lever to the OPEN position. The damper is opened and room air is exhausted. 2 Notes Avoid opening doors and windows unless necessary. Don't be exposed to cold air for a long time. a little bit higher before going to bed. Proper temperature 2 Air filter cleaning When dirt accumulates on air filter, air circulation will be blocked, which causes poor cooling. It is advisable to clean air filter every two weeks for longer operation. Take out the air filter 1. Loose the air inlet by pushing "PUSH" at both edges as shown. Clean the filter CAUTION Before cleaning, turn off the power. Do not circumgyrate the front panel any more than 90° to the unit or damage to the tabs may occur. PUSH 3 Airflow Direction Airflow Direction Vane The Vertical Airflow Direction Vane is manually controlled by positioning the vane to discharge the air upward, downward or straight out. Use curtain or blind Direct sunlight may reduce cooling effect, always use window curtain. Keep heat source away from air conditioner. After unit stops, don't restart it until 3 min. have elapsed. Air filter(inside) OK!Enjoy a 3-min nap 1. Gently flap the dirt off the air filter. 2. Carefully wash air filter in warm water(below 40°C). To obtain better cleaning effect, soap water or neutral detergent may be used. 3. Flush air filter carefully with clean water after removing dirt. Let it dry completely. Installation of filter 1. Replacing the air filter. 2. Push the air inlet marked with "PUSH" until you hear a click. PUSH Don't hang clothes in the vicinity of air inlet. This will decrease cooling effect and cause abnormal operation. Temperature should be set properly when there are infant, child, the aged or disabled in the room. Before operating mode selection switch, check that if the air inlet or outlet have been blocked. The horizontal air direction is adjusted by setting the AUTO SWING switch to the ON position. Baby has gone sleep, better to adjust suitable temp. 4 AIR CONDITIONER INSTALLATION 1, The air-conditioner is better installed in shadow or in a place with short period of sunshine. In case the air-conditioner is installed at the point exposed directly to the sunshine, it should be protected from the direct sunlight as possible in order to avoid the long time of direct sunlight otherwise its performance will be lowered. For the convenience of operation, it is recommended that air-conditioner be installed at least at the height of 760-1300 mm above the floor and no obstacles before it for a free airflow. 3. The shutters at both sides and the top of air-conditioner should be protruded outdoors free from being blocked by wall, window, ect. [. . . ] Always use at the rated voltage and with specfic air conditioning circuit Figure Quantity 1 1 1 1 5 TROUBLESHOOTING 57 68 Before calling for service. Check the following points before calling for repairs or service. Iron frame NOTE:Your model will have one Drain elbow of the above two, not both. PREPARATIONS BEFORE INSTALLATION Make the wall hole or window hole (see Fig. 1) MODEL HW-09CV03 HW-12CV03 HW-09CVA03 HW-12CVA03 HW-18CV03 HW-18CVA03 A 355mm B 535mm A Phenomenon Cause or check points Solution B 420mm 580mm Fig. 1 Width of the wall Switch on the machine but it does not work immediately. If the machine is started after stop, it will need about 3 minutes to re-start so as to prevent the fuse from break. Prepare unit for installation: 1. Take out the conditioner and accessories from the package . 2. Disposal of the condensed water. Switch on the machine but it does not work. Is plug firmly inserted?Is there power failure? Readjust power supply Does fuse get burned? Replace fuse. Rubber lid Block the bottom plate hole of the conditioner with rubber lid, install drain elbow on the back hole and let the condensing water flow from the back hole of the conditioner. [. . . ]