User manual HAIER L20AV6A-A0

[. . . ] 4 Installing Batteries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Connection Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Grounding. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 External equipment Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Antenna Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV. - For further information regarding cable TV service, contact your local cable TV service provider(s). Connection Option 1 1. Select 3 or 4 with channel switch on cable box. Tune the TV channel to the same selected output channel on cable box. Select channels at the cable box or with the cable box remote control. Connection Option 2 1. Connect the audio and video cables from the Cable Box's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to a Cable Box, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). Select the input source by using the TV/AV button on the remote control. Select your desired channel with the remote control for cable box. External AV Source Setup How to connect Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). How to use 1. Select the input source by using the TV/AV button on the remote control. Operate the corresponding external equipment. MIX Button Press MIX button to enter Teletext mode and both the TV picture and text page can be visible. TIME While in normal TV mode only, pressing the button TIME will display the teletext time in the top right corner for a few seconds. Menu Operations * In this manual, the OSD (On Screen Display) may be different from your TV s because it is just an example to help you with the TV operation. 1. Press MENU button to either display the PC MENU or TV MENU or VIDEO MENU or GENERAL MENU or AUDIO MENU in different source inputs. Press P+/P- to scroll through the parameters 3. Press V+/V- buttons to make changes to the parameters 4. Press the OK button to exit the menu Picture Menu Options Picture quality can be adjusted for any input separately . The picture quality on the screen can be adjusted as follows: 1. Press MENU button until the following menu appears on the screen. PC MENU PC MENU BRIGHTNESS CONTRAST COLOR SETTING AUTO CONFIG H-POSITION V-POSITION PHASE CLOCK 50 50 9300K 50 50 50 50 AV/S-VIDEO MENU VIDEO MENU BRIGHTNESS CONTRAST COLOR HUE SHARPNESS 50 50 50 50 50 Menu Operations Picture Menu Options Continued TV MENU VIDEO MENU BRIGHTNESS CONTRAST COLOR HUE SHARPNESS 50 50 50 50 50 2. Press P+/P- button to enter the picture menu and to go up and down to select the desired option . 3. Press V+/V- button to increase and decrease the level to adjust the selected option to your preference . [. . . ] 3. Press V+/V- button to adjust the selected option to your preference . Repeat step 2 and step 3 until desired quality has been achieved . . Functions: 1. BLUE SCREEN : You can set it ON or OFF . If select ON and there is no signal , the screen will display blue screen 2. NOISE REDUCE : select OFF/LOW/MID/HIGH to reduce the noise of the picture , provide clearer picture . [. . . ]