User manual HAIER NS-13CTV

[. . . ] 13 NS-13CTV PRECAUTIONS FCC Statement FCC NOTICE CLASS B DIGITAL DEVICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions in this manual, may cause harmful interference to radio communications. CAUTION: Pursuant to 47CFR, Part 15. 21 of the FCC rules, any changes or modifications to this device not expressly approved by the manufacturer could cause harmful interference and would void the user's authority to operate this device. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures to counter interference LOCATION:INSIDE, NEAR THE DECK MECHANISM. CONTENTS Before Operation Warning and cautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Fine Auto Program Auto TV off 2 Follow the procedure below to select above options: 1. Press the CH(+) and CH(-) button to go up and down the menu. 2. Press VOL (+) button or VOL (-) button to select your preference. Channel System: Press the VOL(-/+) buttons to select the correct channel system. In general, you can set it as "AUTO" AUTO, NTSC and NTSC443 will display in turn Antenna: Press VOL (+) button or VOL(-) button to select TV or CATV. Skip : Press VOL(+) button or VOL(-) button to add or delete the channel from the stored memory. : Press VOL(+) button to go up and VOL (-) button to go down to set the channel position. The display will show the current playing channel. Channel Coverage by Antenna: Antenna Type Channel Range VHF 2-13 UHF 14-69 CATV 1-125 Fine: If the picture and/or sound are poor, try using the FINE TUNE feature. Do not use this feature unless reception is poor. Press VOL (+/-) to start the Fine Tune function. Auto Program: Press VOL (+) button to auto program in channels. This search automatically adds only the active channels in your area to the TV's memory. It deletes any channels on which there is no broadcast or a poor signal. Note: The Auto Search function will scan the channels on the selected antenna input. If the TV is connected to cable, please select Cable under Antenna. Calendar: Your TV has been designed with a calendar. By pressing MENU button , and then pressing VOL(-/+) buttons it will bring you to Calendar. You will see the following display on TV screen. OCT OCT OCT Calendar 2005 9 14 Follow the procedure below to adjust the Calendar quality: 1. Press the CH( +/-) buttons to select the year item, the month item or the date item. Press the VOL(-/+) buttons to change calendar setup . Press EXIT button to exit the calendar mode. V-CHIP Setup: Press the MENU Button on your remote control to go to Password menu, then input the password (0000). It will bring Parental Lock set up display on the screen. You will see the following menu on your screen: Passsword Parental Lock Password ---- Parental Lock TV Rating MPAA Rating Lock Menu Change Password off This function enables you to lock certain TV channels in accordance to the V-CHIP requirement established by the FCC. [. . . ] (Initial password is 1234) 2 When set to OFF, all discs may be viewed. DVD System Setup(Continued) DVD System Setup PASSWORD CHANGE: SETUP You can change your password by entering 4 digits. You must confirm the 4 digits before the new password can be accepted. . . Preference Page. . Parental Password Default Change PLAY/ENTER Old Password New Password Confirm Pwd NOTE:If you forget your password or a password is accidentally set enter 1369 as the password. This will enable you to regain control. SETUP DEFAULT: Resets all settings (except password and parental lock status) for this DVD player back to the manufacturers original settings. [. . . ]