User manual HANNA INSTRUMENTS HI 3844

[. . . ] Instruction Manual SPECIFICATIONS Range 0 to 2 ppm H2O2 Low Range 0 to 10 ppm H2O2 High Range Smallest Increment 0. 25 ppm H2O2 Low Range 1. 0 ppm H2O2 High Range Analysis Method Drop-Count Iodometric Titration Sample Size 25 mL Low Range 5 mL High Range Number of Tests 100 (average) Case Dimensions 235x175x115 mm (9. 2x6. 9x4. 5") Shipping Weight 450 g (15. 9 oz. ) INSTRUCTIONS READ THE ENTIRE INSTRUCTIONS BEFORE USING THE KIT · Remove the cap from the plastic vessel and rinse it with sample. For H2O2 Low Range fill it up to the 25 mL mark with the sample. [. . . ] The kit is portable and can be used in the field as well as in the laboratory. Note: mg/L is equivalent to ppm (parts per million). 12/99 Dear Customer, Thank you for choosing a Hanna Product. Please read the instructions carefully before using the chemical test kit. It will provide you with the necessary information for correct use of the kit. Remove the chemical test kit from the packing material and examine it carefully to make sure that no damage has occurred during shipping. If there is any noticeable damage, notify your Dealer or the nearest Hanna office immediately. Each kit is supplied with: SPECIFICATIONS · HI 3844A-0 Hydrogen Peroxide Reagent, 1 bottle (100 mL) ; · HI 3844B-0 Hydrogen Peroxide Reagent, 1 bottle (17g) ; · HI 3844C-0 Hydrogen Peroxide Reagent, 1 bottle with dropper (30 mL); · HI 3844D-0 Hydrogen Peroxide Reagent, 1 bottle with dropper (25 mL) · 1 plastic test tube, graduated with cap; · 1 calibrated plastic vessel (50 mL); · 1 plastic pipette (3 mL); · 1 plastic pipette (1 mL), for HI 3844A-0 Reagent; · 1 plastic spoon. Note: Any damaged or defective item must be returned in its original packing materials. · Add 1 mL of HI 3844A-0 reagent for Low Range or 0. 5 mL for High Range using the plastic pipette and swirl gently to mix. · Add 2 to 3 drops of HI 3844D-0 reagent and mix by carefully swirling the plastic vessel in tight circles. · Continue adding slowly drops of the titration reagent HI 3844C-0, while swirling and counting the drops, until the solution changes from blue to colorless. · To obtain the concentration in ppm of Hydrogen Peroxide in your sample, multiply the total number of drops of the titration reagent HI 3844C-0 used to turn the solution from the dark yellow color to colorless by 0. 25 or 1 for Low Range or High Range, respectively. # of DROPS * 0. 25 = ppm Hydrogen Peroxide LR # of DROPS * 1 = ppm Hydrogen Peroxide HR · Using the plastic spoon provided, add 1 spoon of HI 3844B-0 reagent and swirl gently to mix. Note: Note after a few minutes, the blue color of the starch/ iodine complex may reappear after the titration has been completed due to air oxidation of the iodine. REFERENCES Vogel's, Textbook of quantitative chemical analysis, 5th ed. , Longman Scientific and Technical CHEMICAL REACTION Hydrogen peroxide is determined by a titrimetric method. It reacts slowly with iodide in acid solution (Step 1); thus a 15 minutes interval is required to allow the reaction to occur completely. [. . . ] Continue adding the titration solution until the yellow color of the solution is almost colorless. HEALTH AND SAFETY The chemicals contained in this test kit may be hazardous if improperly handled. Read Health and Safety Data Sheets before performing the test. ISTR3844 [. . . ]