User manual HANNA INSTRUMENTS HI 955201

[. . . ] Untitled-10 1 2 Instruction Manual HI 955201 - HI 955202 HI 955301 - HI 955302 Portable Microprocessor Printing and Logging PT-100 Thermometers Dear Customer, Thank you for choosing a Hanna Instruments Product. Please read this instruction manual carefully before using the instrument. This manual will provide you with all the necessary information for the correct use of the instrument, as well as a precise idea of its versatility in a wide range of applications. These instruments are in compliance with directives EN 50081-1 and EN 50082-1. [. . . ] The printout provides the following information: a 10-01-96 d ==07== 0005M b 0014 *14. 25 c e a - Date (DD-MM-YY) #1 25. 0 °C. b - A running log number c - Running sample number (in that particular lot) d - Printing interval indicator in minutes e - Time (HH-MM) f - Temperature value/s 19 LOGGING MODE WITH PRINTING This function is suggested when an immediate report of the measurement is required in addition to the recording of the data into memory. Press the ALT and LOG keys simultaneously to enter the logging mode. The log number and page number will appear for a few seconds on the display to indicate the correct operational mode. The printer will print a complete set of data and the "LOG" symbol will appear on the bottom left corner of the display. ALT UP DOWN TEMP TIME LOG LOG 20 Untitled-10 21 22 If no key is pressed, the display goes blank after about 5 minutes. During printing, the display shows the time, interval and the "LOG" symbol. · TIME LOG INTV · · To reactivate the display press the TEMP key. TEMP The printout provides the following information: a - Date (DD-MM-YY) b - A running log number c - A running sample number (in that particular log) d - Printing interval indicator in minutes e - Time (HH-MM) f - Temperature value/s g - Channel # (HI 955302 only) It is always possible to switch from the logging with printing function to the logging only function. Press the ALT and the PAPER keys at the same time and the "LOG" symbol will start to blink to indicate that the data are now stored only into memory. b c 10-01-96 ==07== 0005M 0014 *14. 25 #1 25. 0 °C. a d e f °C · Before proceeding with logging and printing, make sure there is enough paper for your measurements. When the paper is finished the meter will not advise the operator and the printouts could be lost. If this happens, data will continue to be stored into memory, and it is always possible to print them at different time (see above). It is possible to insert a new paper roll during logging session (see page 31) Once in the logging mode, the interval cannot be changed. Exit the logging mode first (pressing the ALT and the LOG keys) before setting the new interval. If the PRINT key is pressed while in logging mode, a printout is produced without affecting the PRINT running sample number. ALT UP DOWN TEMP TIME LOG TO STOP LOGGING Press ALT and LOG keys simultaneously, this will generate a log exit status printout. ALT UP DOWN TEMP TIME LOG Log number Total sample number ==07== 0016 10-01-96 0005M *16. 25 LOG EXIT Date/Time PRINT PAPER LOG CH ALT UP Notes: · It is recommended to use the adapter during logging with printing mode, especially when many printouts are going to be taken. 21 22 Untitled-10 23 24 TO SCAN STORED DATA ON DISPLAY Press the LOG key. The display will show the log number and the page number of the next logging. Press UP and the temperature will be displayed. °C CH LOG While pressing the ALT key, press DOWN until the log number to scan appears on the secondary display. The primary display will show the number of samples of that particular log. Continue pressing UP to display all the memorized data of the same log one by one in the above sequence i. e. Press the DOWN key to revert back to sampling time and move back through samples. To exit from the recall mode press LOG. ALT DOWN LOG Note: this mode will not alter data into memory Press ALT and TEMP simultaneously. This now shows the date on which the log started. ALT DATE TEMP Press UP and the time will be displayed. TIME UP TO PRINT STORED DATA Once a log number is selected by using the ALT and DOWN, as detailed in the chapter "TO SCAN STORED DATA ON DISPLAY" you can print all or part of that log section by using the ALT and PRINT keys. The printer will start to print the logged section beginning with the selected sample number without altering the content of the memory. Note: It is always possible to print only the sample shown on the display by pressing PRINT. ALT DOWN PRINT ALT PRINT 23 24 Untitled-10 25 26 Note: Before proceeding with printing, make sure there is enough paper for the data to be printed. When the paper is finished the meter will not advise the operator and printouts could be lost. If this happens, stop the printer by pressing ALT PAPER and PAPER simulta- PRINT neously. [. . . ] Replace the battery cover and secure screws. - 1. 5V 1. 5V 1. 5V 1. 5V + + + - + - SCREW POTS RESET Insert the paper edge in the printer slot and feed the printer by pressing the PAPER key. PAPER 33 34 Untitled-10 35 36 BATTERY REPLACEMENT If "LO BAT" appears on the display, it is an indication that the batteries are running down. If it appears during printing, it means that 200 printouts can be made before the batteries are exhausted. When there is only sufficient power for 100 printouts, the "LO BAT" sign is displayed continuously on the LCD. °C CH Note: The instrument uses the following configuration. + - LOBAT Battery replacement must only take place in a non hazardous area using the battery types specified in this instruction manual (see page 35). It is recommendable to purchase Hanna Instruments HI 710005 and HI 710006 voltage adapters that use the proper polarity configuration. HI 955201, HI 955202, HI 955301 and HI 955302 can also be used with other adapters. [. . . ]